Search:

Type: Posts; User: Keith Outten; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.73 seconds.

  1. Thread: D-Day

    by Keith Outten
    Replies
    54
    Views
    2,587

    Gentlemen, please don't take this thread into the...

    Gentlemen, please don't take this thread into the political side of the topic.
  2. I don't believe in changing oil based on time....

    I don't believe in changing oil based on time.
    Oil never/ever loses its lubricating qualities, it gets dirty from engine miles including start and stop cycles.
    This is how oil change policy was...
  3. Can you see this pic? 459411 How about this...

    Can you see this pic?

    459411

    How about this one?

    459412
  4. Replies
    26
    Views
    1,811

    I think the SR-71 still has the fastest time...

    I think the SR-71 still has the fastest time traveling from the west to the east coast. It set the record on its last flight.
  5. Replies
    19
    Views
    910

    I purchased the small Honda tiller several years...

    I purchased the small Honda tiller several years ago. It's been a great machine for getting into small spaces, absolutely reliable.
    I have an 84" tiller for the big stuff :)
  6. Replies
    100
    Views
    5,692

    Imagine an American child who cannot read the...

    Imagine an American child who cannot read the Declaration of Independence or the Constitution :(
  7. Thread: D-Day

    by Keith Outten
    Replies
    54
    Views
    2,587

    D Day Letter: 458992

    D Day Letter:

    458992
  8. Replies
    8
    Views
    462

    I agree. I have two of them in my shop one for...

    I agree. I have two of them in my shop one for the shop area and one for my office upstairs.
  9. Replies
    29
    Views
    1,302

    Just a thought for any of you who use ash for...

    Just a thought for any of you who use ash for projects if you have drops that can be cut into 8" by 10" plaques you can sell them to people who laser engrave. Smaller 5" by 7" and larger 10" by 12"...
  10. Replies
    9
    Views
    837

    Brazing is your best bet and a really good welder...

    Brazing is your best bet and a really good welder or pipe-fitter would increase your chances of a successful repair.
    Jason is right about the pre-heat and you will need to control how fast it cools...
  11. Replies
    1,382
    Views
    136,981

    458662458664458665458667

    458662458664458665458667
  12. Replies
    9
    Views
    879

    Looks good Tom. I have made a few custom tractor...

    Looks good Tom. I have made a few custom tractor attachments in the past, its' very enjoyable to make your own and save some money.
  13. Replies
    20
    Views
    6,366

    We have been invited to Aaron and Kathy's house...

    We have been invited to Aaron and Kathy's house for Memorial day dinner. Jackie and I will both make every effort to at least get something on the schedule but I was told a few days ago that Aaron...
  14. That's a lot of work to load and unload in one...

    That's a lot of work to load and unload in one day. My back would be killing me the next morning.
  15. Replies
    68
    Views
    4,734

    I use a set of Bose earbuds with noise canceling...

    I use a set of Bose earbuds with noise canceling and my iPhone in my shop, lawnmower and tractor. For the quiet times I have an older Bose Sound Dock with an iPod attached. It's rare these days but...
  16. You may be searching for a version of the...

    You may be searching for a version of the Xenetech software that has serious problems which might account for why they cannot find a copy of that version.
    ...
  17. Replies
    18
    Views
    2,079

    I made these for Dennis. There are plenty of...

    I made these for Dennis. There are plenty of laser engravers here, visit the Laser Forums.
  18. Replies
    4
    Views
    854

    I operated an EBAC dehumidifier for ten years and...

    I operated an EBAC dehumidifier for ten years and it produced the best quality lumber I have ever seen. Your kiln is very close to the one I built, you are going to enjoy the fruits of your labor I...
  19. Replies
    5
    Views
    1,687

    Have you searched our archives? I know I have...

    Have you searched our archives? I know I have seen several CNC air vent drawings over the years but I can't remember if there were any uploaded here.
  20. Replies
    18
    Views
    2,079

    Do a search here on Wooden Medallions.

    Do a search here on Wooden Medallions.
  21. Replies
    141
    Views
    10,734

    The topic of this thread is Electric Car...

    The topic of this thread is Electric Car Challenges.
  22. Replies
    1,382
    Views
    136,981

    Thanks Paul, got a good laugh from the video :)

    Thanks Paul, got a good laugh from the video :)
  23. I never have changed the one inch blade on my FB...

    I never have changed the one inch blade on my FB 610. I have the 10" Rikon for tight cuts and it is mounted on a piece of plywood that fits the top of a cheap plastic cart I purchased for the Rikon....
  24. Replies
    141
    Views
    10,734

    Dan has asked the most important question. If you...

    Dan has asked the most important question. If you expect to convert 25% of the countries gas powered vehicles to electric you better start building power plants today. Nuclear plants take about...
  25. Tonight 4-25-21 converting JPG to 3D model online class

    Michael Mezalick
    Our most requested topic!
    JPG to 3D Model
    Sunday 4-25-2021 at 5PM EDT
    Hope to see you there.

    Link for the class:
    https://youtu.be/4fQFUD0Xm80

    Picture:
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4