Search:

Type: Posts; User: John TenEyck; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.60 seconds.

  1. It won't feel slippery, more like silky. Your...

    It won't feel slippery, more like silky. Your hand will glide over a rubbed out handrail, but won't slip if you grab it. If you prefer no wax use a synthetic pad or brass wool and soapy water to...
  2. Replies
    2
    Views
    97

    No experience but I would think either product...

    No experience but I would think either product would bond fine over a properly cleaned and scuffed OB paint, since both are oil modified products. Of the two, Emerald Urethane Trim paint dries and...
  3. If you want that silky feel rub it out with 0000...

    If you want that silky feel rub it out with 0000 steel wool and paste wax. It will have a nice satin sheen (higher than Rubio Monocoat) and feel amazing.

    John
  4. Replies
    13
    Views
    557

    There's really nothing complicated about a HVLP...

    There's really nothing complicated about a HVLP conversion gun and compressor. You buy the gun you need that will spray what you want and then you buy a compressor that will deliver the necessary...
  5. Replies
    17
    Views
    468

    As a couple of others said - spade bit. I've...

    As a couple of others said - spade bit. I've done it a couple of times and the long-pointed ones work at pretty extreme angles. I had an odd size hole to drill, too, and took a larger spade bit and...
  6. Replies
    13
    Views
    557

    Of course not, Steve. The needle on the purple...

    Of course not, Steve. The needle on the purple HF is something like 1.4 mm, and it's a gravity gun. No way it will spray latex wall paint well, even with substantial thinning. The viscosity of...
  7. Replies
    12
    Views
    811

    Both of the drum sanders I have owned I bought...

    Both of the drum sanders I have owned I bought used. The current one needed to have the drums on one side shimmed up a few thousandths to get it parallel with the bed. The prior owner, a...
  8. Replies
    13
    Views
    557

    True, but the $20 purple Harbor Freight gun...

    True, but the $20 purple Harbor Freight gun sprays beautifully, too. Cheap guns spray really well, not quite as well as more expensive ones, but really well. They just don't last nearly as long...
  9. Dawn or Palmolive dish soap in warm water will...

    Dawn or Palmolive dish soap in warm water will remove the dirt and oil w/o harming the underlying finish. A razor blade works well for shearing paint specs off a finish. All finishes are nontoxic...
  10. Replies
    13
    Views
    557

    The simplest answer is to get an Earlex HVLP...

    The simplest answer is to get an Earlex HVLP turbine unit. Most bang for the $'s and guaranteed to work.

    Interesting that you bought that Husky gun, since it says not suitable for latex paint...
  11. Replies
    12
    Views
    811

    The G0458Z is only $1100 new. $1000 for a used...

    The G0458Z is only $1100 new. $1000 for a used one is a poor deal unless it has a lifetime supply of sanding media with it. I'd keep looking for a better deal on a used machine. If time forced me...
  12. Replies
    29
    Views
    3,262

    Did anyone mention using a support strap on the...

    Did anyone mention using a support strap on the outside of the laminations to prevent them from breaking going around the form? That's pretty common practice for making tight bends, and it allows...
  13. Replies
    86
    Views
    4,661

    I would get the one that's at least 12" wide. ...

    I would get the one that's at least 12" wide. Seriously. I started with a 10" J/P and now have a 14" but still often wish for wider. Everything gets easier on a wider machine. Long beds are nice,...
  14. Replies
    7
    Views
    525

    That's some really nice work. Are those glass...

    That's some really nice work. Are those glass shelves?

    John
  15. The speed on my G0636X that I started this post...

    The speed on my G0636X that I started this post with is 4500 fpm.

    SPECIFICATIONS:

    Motor: 5 HP, 230V, single-phase, 22A
    Max. cutting width left of blade: 16-1/2"
    Max. cutting height...
  16. The feather board you see is 12" high, but you...

    The feather board you see is 12" high, but you can make it any height you want by adding/subtracting rollers. The rollers stay in place for all resaw and veneer slicing, regardless of board height. ...
  17. Richard, this link should take you to the correct...

    Richard, this link should take you to the correct page: https://sites.google.com/view/jteneyck-woodworker/current-projects/tall-bandsaw-feather-board?authuser=1

    There is a SketchUp model at the...
  18. I did look at those slices of Sapele. I...

    I did look at those slices of Sapele. I commented about how good they looked and how well the Woodmaster CT cut even at that low tension. But again, you are missing the point about adequate...
  19. Good point, Will. Nothing else matters much if...

    Good point, Will. Nothing else matters much if the blade isn't sharp and I will add, with equal set on both sides. And that last point is one major advantage for carbide blades. They have no set,...
  20. Mike, if you're happy that's all that matters. ...

    Mike, if you're happy that's all that matters. 12 ksi is half of where the Woodmaster CT performs best. Your photos shows it still performs well, but I'm sure at a pretty slow feed rate. If you're...
  21. Holy cow, about $900 for that. It looks well...

    Holy cow, about $900 for that. It looks well made and maybe it has its place for folks who only need to make small quantities of veneer, etc, and with a lot of patience to glue the stock to the...
  22. I don't think anyone is suggesting that drift is...

    I don't think anyone is suggesting that drift is solved by high tension, certainly not me. But once your saw is set up to cut straight adequate tension makes it easier for the blade to cut straight...
  23. Oh, yes I did. Thanks for catching that. It now...

    Oh, yes I did. Thanks for catching that. It now reads the correct value of 0.10".

    John
  24. Replies
    13
    Views
    878

    Geez, that doesn't look near as bad as I had...

    Geez, that doesn't look near as bad as I had envisioned from your first post. Have you tried buffing it with a power buffer or buffing pad on your ROS?

    John
  25. 4 I don't know what the tension is on your...

    4


    I don't know what the tension is on your saw at the 1" mark, but on mine it's 24 ksi. Actually, I think I do know, and it's not 24 ksi. The FB 510 can't apply that much on a 1" blade with...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4