Search:

Type: Posts; User: Matt Day; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.64 seconds.

  1. OP said he didnít want to rent a trailer and was...

    OP said he didnít want to rent a trailer and was going to take it apart anyway to clean it up.
  2. Replies
    5
    Views
    103

    As usual Lowell, itís some kind of spam. Just...

    As usual Lowell, itís some kind of spam. Just google this kind of thing.

    https://www.npr.org/sections/alltechconsidered/2015/08/24/434313813/why-phone-fraud-starts-with-a-silent-call
  3. Replies
    10
    Views
    474

    You havenít bought that yet, and nobody else has...

    You havenít bought that yet, and nobody else has yet?! This is the third one Iíve seen in the last few months thatís been too far away for me to get my hands on. The search goes on.
  4. Thread: admin

    by Matt Day
    Replies
    4
    Views
    246

    Keith Outten is the moderator for this forum.

    Keith Outten is the moderator for this forum.
  5. Replies
    3
    Views
    347

    That is a nice looking machine at an even nicer...

    That is a nice looking machine at an even nicer price! Good luck with your sale OP, and let me know if you have an edge sander for sale ;-)
  6. Do as Bill says, but use the engine hoist to...

    Do as Bill says, but use the engine hoist to secure the beds while removing them so they donít fall off. 100 pounds a piece sounds about right.

    Bring ziplock bags and a sharpie to label all small...
  7. Iím guessing he holds the piece to be cut with...

    Iím guessing he holds the piece to be cut with one hand and pushes the biscuit joiner with the other.

    Does the blade of the BJ have a flat tooth?

    I like this much better than wrestling a big...
  8. Itís a terrible idea. Similar to using it to cut...

    Itís a terrible idea. Similar to using it to cut meat. chips will go everywhere, like youíre spraying your saw with a hose, and itíll rust.
  9. Honestly, Iíve never worried much about below...

    Honestly, Iíve never worried much about below table dust collection. The above table dust is what gets in your gave and lungs. Currently have my saw raised up about 3-4Ē and have a floor register on...
  10. Replies
    30
    Views
    998

    Lots of people like Grizzly, just not Andy ;-) ...

    Lots of people like Grizzly, just not Andy ;-)

    He likes American old iron, as I do, but Grizzly makes good stuff too.
  11. Replies
    30
    Views
    997

    The ďfunny picturesĒ are called memes.

    The ďfunny picturesĒ are called memes.
  12. Replies
    30
    Views
    998

    Not a hybrid saw. A 3hp cabinet saw if youíre...

    Not a hybrid saw. A 3hp cabinet saw if youíre buying new, or an older 1.5hp+ saw like an older Uni or PM66.
  13. Replies
    9
    Views
    361

    Bill, googling it finds this:...

    Bill, googling it finds this:
    https://www.grizzly.com/products/Grizzly-10-3HP-220V-Cabinet-Table-Saw-with-Long-Rails-Riving-Knife/G0691

    OP, it makes it easier for us to give you advice if you...
  14. Replies
    30
    Views
    998

    Going from the PM Artisan saw to a hybrid isnt...

    Going from the PM Artisan saw to a hybrid isnt going to be a huge upgrade I donít think. Moving a Unisaw or PM66 or G1023 down stairs isnít hard with 2 average strength guys and a hand truck. Take...
  15. Your 3/8Ē plywood likely is thinner than that....

    Your 3/8Ē plywood likely is thinner than that. Make sure it isnít thinner than your track or your plan wonít work.
  16. Replies
    57
    Views
    1,865

    Pics of exactly what youíre talking about would...

    Pics of exactly what youíre talking about would help. There might be tapered pins or roll pins holding it on, which would need to be knocked out with a punch.
  17. Replies
    62
    Views
    2,917

    Looking good! Iíve been busy with family stuff...

    Looking good! Iíve been busy with family stuff but hopefully Iíll be painting soon too. Iím using the Acrylic version of the DTM, which only has 250g/L.

    Assembling a fresh restoration is one of...
  18. Replies
    11
    Views
    486

    I recently installed a CV1800, with upgrades 16Ē...

    I recently installed a CV1800, with upgrades 16Ē impeller and have been very happy. The EF5 was a lot more expensive, and I didnít see the cost/benefit working out, and I didnít have the ceiling...
  19. Replies
    4
    Views
    899

    You need to list a price based on forum rules.

    You need to list a price based on forum rules.
  20. Replies
    14
    Views
    394

    Thank you for all the advice so far. First...

    Thank you for all the advice so far.


    First we went from a simple table with a shelf, no she sent me this image thinking she wants more storage. But there are all kinds of expansion/contraction...
  21. Replies
    14
    Views
    394

    Very good points, thanks Dom.

    Very good points, thanks Dom.
  22. Replies
    14
    Views
    394

    Doís and Doníts of outdoor furniture

    I havenít made any outdoor furniture except PT utility type stuff. I have a client that wants a Big Green Egg table. Iím thinking about White oak or cedar, or cedartone from Menards (speaking of...
  23. Replies
    29
    Views
    797

    Guys - there is no access to the anchor - how on...

    Guys - there is no access to the anchor - how on earth would a toggle or roc loc or whatever else you are suggesting work in this situation? And a French cleat would lift off. Please consider the...
  24. Replies
    57
    Views
    1,865

    Bummer! Sorry that I shouldíve explained more...

    Bummer! Sorry that I shouldíve explained more about using a hammer with brittle cast iron.

    When I remove bearings I usually press them out using a bearing puller. In that case I would hook the...
  25. Thread: Bondo

    by Matt Day
    Replies
    20
    Views
    783

    That guy wasnít very smart.

    That guy wasnít very smart.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4