Search:

Type: Posts; User: Dueane Hicks; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    2,058

    Walker turner machines uses Proprietary bearings...

    Walker turner machines uses Proprietary bearings that are VERY hard to find. This size does not have a alternative bearing that you can buy that will work in their machines. I ran into this restoring...
  2. Replies
    1
    Views
    897

    Removed from listing.

    Removed from listing.
  3. Replies
    1
    Views
    897

    Fuji MPX-30 Spray gun. Low pressure

    I bought this gun a few years ago for my rekindled cabinet making dreams. Only used it One time (Yes, only once). Anyway; Please look up the gun for specs. It is essentually new and spotless. I also...
  4. Replies
    5
    Views
    1,629

    PB blaster is also a good choice for cleaning them

    PB blaster is also a good choice for cleaning them
  5. Replies
    4
    Views
    1,161

    Well done!

    Well done!
  6. Replies
    19
    Views
    4,120

    Cherry lends itself to twice turning.

    Cherry lends itself to twice turning.
  7. The Nova rest is no where near as tough as the...

    The Nova rest is no where near as tough as the robust. Mine gave way as the weld broke. They are probably ok on smaller lathes and sizes. I have several of the modular box rests and they are good.
  8. Replies
    10
    Views
    2,709

    I ordered one. I go through pencils like a pencil...

    I ordered one. I go through pencils like a pencil maniac
  9. Replies
    27
    Views
    6,221

    I just loop a piece of masking tape, write info...

    I just loop a piece of masking tape, write info on it, then use a small tack to stick it on the blank
  10. Replies
    6
    Views
    2,730

    Another vote for frugal vacuum pumps. I just keep...

    Another vote for frugal vacuum pumps. I just keep mine in a old 4 drawer file cabinet right next to the lathe, with the drawer open when I need to plug it into the vacuum chuck.
  11. Replies
    2
    Views
    1,538

    Very nice!

    Very nice!
  12. Replies
    3
    Views
    2,292

    I had one back in the 90's. Good lathe, but the...

    I had one back in the 90's. Good lathe, but the lowest speed is a bit high on those reeves drive olivers. Built for commercial use in pattern making
  13. Replies
    13
    Views
    2,700

    I also use the Oneway bowl steady. I may try two...

    I also use the Oneway bowl steady. I may try two of them for a bit more control on hollow forms.
  14. Replies
    24
    Views
    5,327

    I would suggest a bi metal lenox blade, as they...

    I would suggest a bi metal lenox blade, as they last much longer and can be resharpened several times with a cheap diamond grinding sleeve on a dremel. Those so called "turners blades" seem to go...
  15. Replies
    29
    Views
    6,172

    I couldn't walk ten feet in flip flops!

    I couldn't walk ten feet in flip flops!
  16. Replies
    12
    Views
    1,883

    Be forewarned: Walker turners have bearings that...

    Be forewarned: Walker turners have bearings that were discontinued a long time ago. Finding them can be quite an ordeal, not to mention, about 50.00 per bearing.
  17. Replies
    29
    Views
    6,172

    Those aching feet

    Would anyone mind putting up a link to a good floor mat to combat bad feet and a sore back?
  18. Replies
    4
    Views
    1,211

    I have had bionic, sellstrom and a useless bubble...

    I have had bionic, sellstrom and a useless bubble type face-shield from craft supplies. Then I tried this one (Lincoln electric omnishield pro) I found the quality is much better than any of the...
  19. Replies
    13
    Views
    2,211

    Just be careful using those made for green wood...

    Just be careful using those made for green wood blades as they are grabby. Always use a jig when cutting round stock on it's side. I got a surprise more than once using an aggressive set blade. In...
  20. Replies
    10
    Views
    2,331

    I had a Titan chuck that was machined poorly and...

    I had a Titan chuck that was machined poorly and wobbled. They said it was how I was using it, it wasn't.
  21. Thank you!

    Thank you!
  22. Homemade laser or video for mcnaughton center saver

    Has anyone come up with their own video, or laser system for the Mcnaughton center saver? I've been using the Oneway easy core, but wanted something that could get blanks from a whole mess of burl I...
  23. Replies
    1
    Views
    1,494

    What a great idea! Thanks for sharing.

    What a great idea! Thanks for sharing.
  24. Replies
    4
    Views
    1,747

    I use 120 as a general sharpening grit on the...

    I use 120 as a general sharpening grit on the sorby proedge. Ceramic seems to be the only thing that holds up to high speed steel. 60 is good for shaping. You have to be careful not to burn the steel!
  25. Replies
    15
    Views
    5,978

    very nice; I wonder how far below the laser...

    very nice; I wonder how far below the laser itself that it will work? For large or deep bowls.
Results 1 to 25 of 172
Page 1 of 7 1 2 3 4