Search:

Type: Posts; User: Si Wood; Keyword(s):

Search: Search took 0.00 seconds.

  1. Replies
    34
    Views
    2,482

    I have used both solvent based ( as in this one )...

    I have used both solvent based ( as in this one ) and water based and have done a LOT of laminating but on particle board for store fixtures and counter tops. I have never laminated pine but I can...
  2. Replies
    4
    Views
    732

    I have not registered with Vintage Machinery and...

    I have not registered with Vintage Machinery and I have tried different devices, cleared cookies, turned off my VPN...everything and no response from the administrator...??? I even posted on the...
  3. Replies
    4
    Views
    732

    Anybody know what's going on with OWWM?

    Hi All. This past week I registered for OWWM and went thru the usual screening, moderated mode and finally approved. Along with that email I got an access password to which got me logged in and of...
  4. Replies
    1
    Views
    4,474

    Very nice Wixification, what a time saver on set...

    Very nice Wixification, what a time saver on set ups that must be. I had Wixified my General 130 a couple years ago, never thought of doing the same for the Shaper...and yet another project ...
  5. We solved that one... Thanks for reaching out,...

    We solved that one... Thanks for reaching out, much appreciated!!
  6. Replies
    42
    Views
    4,391

    That is a solid planer and definitely workable.....

    That is a solid planer and definitely workable.. If you make the purchase, just start from the ground up on all the pertinent adjustments. I bought a portable Grizzly ( a reluctant made in Taiwan...
  7. Am I missing something about private messages

    Hi Everyone...I'm as new as it gets but learning. As a contributor, I have tried twice now to send PM to two separate members ( just didn't see the need to start a new thread as my question relates...
  8. Replies
    54
    Views
    33,315

    Sticky: Hi ALL and Happy Tuesday! I'm not posting to...

    Hi ALL and Happy Tuesday! I'm not posting to ruffle any feathers, mainly just " food for thought " I'm guessing people come here for a variety of reasons and walk away with what they came for, why...
  9. Replies
    21
    Views
    1,560

    If your cutting veneered ply core, you would do...

    If your cutting veneered ply core, you would do well without regrets using a full kerf ( .125 ) 80 tooth alternate tooth bevel ( Hi-ATB ) with at least a neg.15* rake. When your spending that kind of...
  10. Thread: My first post

    by Si Wood
    Replies
    10
    Views
    630

    Thanks Fred. It didn't take long to feel Welcomed...

    Thanks Fred. It didn't take long to feel Welcomed here. Great place to hang out!
  11. Replies
    32
    Views
    2,112

    I would try ripping a different scrap board to...

    I would try ripping a different scrap board to eliminate the possibility that it is a lumber issue. Freshly dressed 8/4 stock, depending on storage environment should be done within a few days time...
  12. Thread: My first post

    by Si Wood
    Replies
    10
    Views
    630

    No harm done at all...I came by seeking ...

    No harm done at all...I came by seeking different views cause i think I had been staring at it too long. Thank yous to Brad. He pointed me in the right direction, so now, I'll start peeling my...
  13. Thread: My first post

    by Si Wood
    Replies
    10
    Views
    630

    Follow up - Those links you shared were the...

    Follow up - Those links you shared were the golden ticket! now.... to dig up dad's puller
  14. Thread: My first post

    by Si Wood
    Replies
    10
    Views
    630

    Thanks Brad I'll check out those links. There is...

    Thanks Brad I'll check out those links. There is a center for a puller pin but with the worm gear being engaged on the bronze makes me nervous...
    Hope all is well down there! We're thinkin bout you...
  15. Thread: My first post

    by Si Wood
    Replies
    10
    Views
    630

    Thanks Ken. Yes I was hoping for a set screw as...

    Thanks Ken. Yes I was hoping for a set screw as well but there isn't one. It looks to me the woodruff key is slipped in as the shaft/cutter head is being re-assembled into position. The bronze gear...
  16. Replies
    8
    Views
    1,126

    Going from a General 350 cabinet saw down to the...

    Going from a General 350 cabinet saw down to the Dewalt 7491RS because of a similar real estate issue has been a real challenge for a guy with tonnes of shop experience. I'm not sure where your going...
  17. Thread: My first post

    by Si Wood
    Replies
    10
    Views
    630

    My first post

    Happy Thursday All! I'm new on board and wanted to stop by, say hello and reach out for help. Here to share and hope I'm able to contribute more than I walk away with.:) I'm hoping someone has taken...
Results 1 to 17 of 17