Search:

Type: Posts; User: Larry Frank; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.52 seconds.

  1. Amazon has all kinds of 10 mm drill bits. I...

    Amazon has all kinds of 10 mm drill bits. I would use a 1/8" drill bit and then a 10 mm brad point bit. I have done similar many times with very good results.

    You can also get some bass wood on...
  2. Thread: saw stop

    by Larry Frank
    Replies
    30
    Views
    1,097

    You said in your original post that you would get...

    You said in your original post that you would get a lot of slack from the post. Exactly, what did you expect to get or want to get for responses? Obviously, the responses were not what you wanted....
  3. Thread: saw stop

    by Larry Frank
    Replies
    30
    Views
    1,097

    I am surprised st this and would like to see a...

    I am surprised st this and would like to see a picture of the problem.

    I think Saw stop has an extremely good fit and finish and excellent assembly instructions. The assembly parts are very well...
  4. Replies
    29
    Views
    1,265

    On bigger ticket items. I use camel camel camel...

    On bigger ticket items. I use camel camel camel to track price history on Amazon. It has saved me a bunch. They just built an Amazon distribution center near me and deliveries have improved. I...
  5. Replies
    47
    Views
    2,241

    How much does a saw with this system cost?

    How much does a saw with this system cost?
  6. Replies
    7
    Views
    503

    I built all my shop cabinets with Aruaco ply. I...

    I built all my shop cabinets with Aruaco ply. I used 3/4" for everything and it worked great. I would use it again if needed.
  7. My Home security system was recently upgraded for...

    My Home security system was recently upgraded for this reason. There was no charge to me for the upgrade.
  8. Replies
    23
    Views
    1,764

    Without the proper instruments, it will be...

    Without the proper instruments, it will be difficult. Even with the proper instruments, it takes effort to get meaningful numbers. I think that there are pretty good performance curves for both...
  9. Replies
    0
    Views
    557

    Wood Spirit

    I am new to carving and doing power carving with a flex shaft tool. This is one of my first and is a Wood Spirit carved from Poplar. I have found so much help on YouTube as I learn. I watched a...
  10. Replies
    64
    Views
    4,801

    I have a question..... Why haven't you posted a...

    I have a question..... Why haven't you posted a picture of your setup ? There are several extremely knowledgeable people who have tried to help and do not understand your issues. Pictures would...
  11. Replies
    64
    Views
    4,801

    I am glad you got it sorted out. I think people...

    I am glad you got it sorted out. I think people could have been more helpful if you had posted pictures. Without seeing your setup people are making their best guess.
  12. Replies
    64
    Views
    4,801

    Why not just measure the suction with a homemade...

    Why not just measure the suction with a homemade water u tube manometer?
  13. Replies
    27
    Views
    1,200

    This thread went way off the rails ! On the...

    This thread went way off the rails !
    On the Medicare website, you can enter your medications and get a good estimate of the costs from various plans. If you know your RX costs without Part D, you...
  14. Replies
    64
    Views
    4,801

    There are quite a few posts where people have...

    There are quite a few posts where people have measured airflow of both the HF and CV1800 or similar. The HF gives you around 650 cfm while the CV1800 and similar are over 1800 cfm. The OP should...
  15. I use Just Watch.

    I use Just Watch.
  16. I have had my Festool for years and love it. ...

    I have had my Festool for years and love it. Worth every penny to me !
  17. Replies
    22
    Views
    1,148

    That is a great video showing how to get at the...

    That is a great video showing how to get at the proper areas.
  18. Replies
    232
    Views
    12,923

    According to the article, the range decreases...

    According to the article, the range decreases 50-60%.
  19. Replies
    12
    Views
    774

    I cut Formica on my table saw with a fine toothed...

    I cut Formica on my table saw with a fine toothed blade. I cut it oversize, apply it and then trim with router bit.
  20. Replies
    232
    Views
    12,923

    I have given though to an electric car. However,...

    I have given though to an electric car. However, the thought of getting stuck on the Interstate during a snow storm or cold scares me. With the cold, battery capability goes down and the ability to...
  21. Replies
    22
    Views
    1,401

    Netgear has a WiFi analytics app for your phone. ...

    Netgear has a WiFi analytics app for your phone. You can use it to measure signal strength at various places in your home. I compared signal strength for my extender and mesh systems. The mesh was...
  22. Replies
    17
    Views
    1,160

    I bought a $50 keyless chuck on Amazon for my...

    I bought a $50 keyless chuck on Amazon for my Nova. Run out is less than 0.005" and very happy with it. For woodworking, it is more than good enough.
  23. Replies
    14
    Views
    1,010

    Ok on second one but do not like the first...

    Ok on second one but do not like the first because lack of symmetry.
  24. Replies
    22
    Views
    1,401

    I had a.Netgear router and extender and they...

    I had a.Netgear router and extender and they worked pretty well. However, I upgraded to a mesh system and it really works. My wife's sewing room had been very difficult and she needed something...
  25. This is certainly an interesting design and...

    This is certainly an interesting design and features. However, the 700 max cfm with 6"duct is kind of low given the price.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4