Search:

Type: Posts; User: Mitchell Ristine; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    768

    .svg for a tele

    Anyone out here have an .svg for a tele? I have a laser guy who will cut a template for me.
  2. 16/32 platen not flat. Lower in the middle

    I bought an older Performax 16/32. As you can see in the photos, the platen dips in middle (front to back). This causes my work to be thinner in the middle.

    Are there any known fixes for this?...
  3. Another drum sander calibration thread

    I have a new to me Performax 16/32. My drum is 3/16 higher on the outside than on the inside. I've watched "Joe the woodworkers" video. Here's my thing, I pulled the spring out of the fine tune...
  4. Replies
    2
    Views
    728

    Flat sand or not

    Hey all, I am making a pedal board for a guitar player I know.
    455054455055

    I am spraying general finishes high performance top coat. I plan on spraying about 5 coats.

    Question: After the last...
  5. Replies
    17
    Views
    1,117

    Not a base. A template. For repetitive cuts.

    Not a base. A template. For repetitive cuts.
  6. Replies
    17
    Views
    1,117

    Cutting Acrylic

    Hi all. I know a guy with a laser. He cut me a router template out of hard board. Initially I wanted an acrylic template but he said that sometimes the laser will skew while going through ...
  7. Replies
    11
    Views
    896

    Thanks everyone. Plywood it is.

    Thanks everyone. Plywood it is.
  8. Replies
    11
    Views
    896

    That's what my gut says too. I've never edge...

    That's what my gut says too. I've never edge banded anything before. Is it difficult?
  9. Replies
    11
    Views
    896

    Plywood or solid

    This is a partial wall from a RV. It's MDF covered in plastic. I've been commissioned to make a new one.
    453554

    It's about 4.5 feet tall and 2.5 feet wide (at the widest point). 0.5 inch...
  10. If you go the grizzly route pay close attention...

    If you go the grizzly route pay close attention to the type of head. Spiral and Helical are NOT the same. It has to do with the orientation of the cutter. Spiral are perpendicular to the wood. ...
  11. Replies
    19
    Views
    1,407

    I should have been much more specific. Sorry. ...

    I should have been much more specific. Sorry. I'm looking for Brand and material for twist jobbers.
  12. Replies
    19
    Views
    1,407

    Drill Bits

    Hey folks, what are your go to drill bits for wood applications?
  13. I am interested in Klingspor. I buy their belts...

    I am interested in Klingspor. I buy their belts for my ridgid sander. My next disc purchase will be from them. If I remember, I'll come back and update.
  14. I have taken to scale drawings whenever possible....

    I have taken to scale drawings whenever possible. I buy rolls of 36" wide white paper. When I am drawing things out I can think through joinery, know my measurements, think about cutting order........
  15. Yup I have used them. They are OK. They're...

    Yup I have used them. They are OK. They're cheaper for a reason. I have noticed that the hook and loop backing on the discs is hit and miss (sometimes I get discs that fly right off my sander. ...
  16. Replies
    10
    Views
    1,185

    I sprayed my cabinets with a graco 390. I used...

    I sprayed my cabinets with a graco 390. I used Sherwin williams pro classic Alkyd Interior Enamel. I brushed the face frames (cannot tell I did). I removed all the hardware, built a spray booth in...
  17. Replies
    49
    Views
    3,766

    I was just emailing with Morgan at Laguna. He's...

    I was just emailing with Morgan at Laguna. He's got a 14SUV for $1,300.00. Probably worth investigating. Not sure I'd pay more than $1,200 for that 15 year old Laguna.
  18. The Griz also has a 1.5 hp motor (Jet is 1).

    The Griz also has a 1.5 hp motor (Jet is 1).
  19. Replies
    27
    Views
    1,635

    I'd love to. I'd happily pay for shipping.

    I'd love to. I'd happily pay for shipping.
  20. Replies
    6
    Views
    6,605

    Yep, neck. Also, it has better resistance...

    Yep, neck. Also, it has better resistance matching to the HB than a single would. 500k CTS pots.
  21. Replies
    6
    Views
    6,605

    Custom neck plate from Philadelphia Luthier Tools...

    Custom neck plate from Philadelphia Luthier Tools & Supplies:
    447258

    My pups are being made as we ... type?
    Bootstrap pickups in Ohio.

    This will be a very heavy metal guitar.
  22. Airline stocks are still very low, they seem to...

    Airline stocks are still very low, they seem to be a reasonable holding place for tech and MBS.
  23. Replies
    27
    Views
    1,635

    I know. I could make it all work but the actual...

    I know. I could make it all work but the actual riser. Getting the pin locations EXACT is necessary and I don't have a milling press or vise.
  24. Replies
    6
    Views
    6,605

    2nd Build ... this time a tele

    I made so many mistakes on my first build I need to do another one just to get some self respect back ;)

    This will be a tele a'la Jim Root. Poplar body. Lyptus neck. Maple fret board. The body...
  25. Replies
    27
    Views
    1,635

    Best place to source a riser kit for an old...

    Best place to source a riser kit for an old delta? On ebay they're going for 250+. Wondering if there's a more cost friendly source.
Results 1 to 25 of 122
Page 1 of 5 1 2 3 4