Search:

Type: Posts; User: Rush Paul; Keyword(s):

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    20
    Views
    1,586

    I am a diehard 2017 Sketchup Make user on a...

    I am a diehard 2017 Sketchup Make user on a Windows 11 PC. I was sorry to see Trimble stop supporting it, and sorry to loose access to the 3D Warehouse that will no longer work in it. But, I begin...
  2. Replies
    16
    Views
    2,444

    +1 on the ClearVue 6" gates. We have a dozen of...

    +1 on the ClearVue 6" gates. We have a dozen of them in our community woodworking shop over the past four years and they've worked just fine. Only problem we've had is one gate that tends to slide...
  3. Replies
    32
    Views
    3,030

    I also use GRK R4 screws for all my projects,...

    I also use GRK R4 screws for all my projects, particularly plywood panel projects. The #8 GRK R4 screws are perfect in 1/2" and 3/4" plywood. I'll also use the #8 GRK Cabinet screws in many locations...
  4. One would think so, and I presume on other units...

    One would think so, and I presume on other units it does, but not ours. In our case, the wing simply crashed down to the travel stop post and refused to budge. After some extensive persuasion, we did...
  5. Replies
    10
    Views
    1,217

    We have a 60HH in our community shop with the...

    We have a 60HH in our community shop with the same problem. After working on it for hours, and puzzling out the parts diagram, we got it set to take a 1/32" cut and left it there. It does work very...
  6. I don't think you're missing anything. We have a...

    I don't think you're missing anything. We have a 60HH in our community shop with the same problem. We got it set to take a 1/32" cut and left it there. It does work very well and very accurately. But...
  7. Yes, you are absolutely correct, Chris. This is...

    Yes, you are absolutely correct, Chris. This is why we constantly cross check against our particle count meter in the shop.
  8. Andrew, the holes are 2.5" or larger with a total...

    Andrew, the holes are 2.5" or larger with a total area of 2.5 times the 6" duct. No material dust accumulation on surfaces in front or behind the saw. Noticeable reduction in collection without the...
  9. Many thanks to all who replied. I found an online...

    Many thanks to all who replied. I found an online source for 1/4" double sided melamine MDF and will plan to go with that solution.
  10. Yes, I understand the insert cannot be cut all...

    Yes, I understand the insert cannot be cut all the way through. :) This would only be for the back fence where I will have enough height to exceed the maximum height of the blade. The zero clearance...
  11. Thank you. I suspected the hardboard would not be...

    Thank you. I suspected the hardboard would not be as consistent in thickness as one would want. Plus, laminating it would add a whole additional variable. MDF may be the right solution here. As...
  12. Laminating Hardboard - Can I get a very flat uniform thickness result?

    Has anyone glued (laminated) 1/4" or 3/16" hardboard? I want to make some dovetailed replaceable inserts for the fence of my cross-cut sled and I'm thinking of laminating two 3/16" thick strips of...
  13. Sorry to hear you can't get your 6" duct from you...

    Sorry to hear you can't get your 6" duct from you 5HP Oneida to the Kapex. But, for what this may be worth to some others, in our community workshop, we set up a downdraft table connected to a 6"...
  14. Replies
    10
    Views
    1,707

    Thanks, Lee. Sorry for the mix up.

    Thanks, Lee. Sorry for the mix up.
  15. Replies
    32
    Views
    5,756

    Bryan, the information about sizing I've seen in...

    Bryan, the information about sizing I've seen in the Australian Woodworking Forum (lots of information on dust collection) is to shoot for a baffle area that is 2x or greater than the outlet from...
  16. Replies
    32
    Views
    5,756

    Nice design on the baffle. For the baffle in our...

    Nice design on the baffle. For the baffle in our shop, we glued and screwed some wall-to-wall pile carpeting (about 3/8-1/2" thick) to the inside walls. Doesn't take up much interior volume and seems...
  17. Rubber mat interlocking tiles flooring across all...

    Rubber mat interlocking tiles flooring across all traffic areas in the shop. Great improvement over the concrete it covers:

    468017
  18. Replies
    64
    Views
    13,968

    Woody, like some others, I'm failing to...

    Woody, like some others, I'm failing to understand how leakage at your filters would in any way affect your overall air flow and suction. But, if you now have the suction at the intake side that you...
  19. Replies
    64
    Views
    13,968

    Woody, this sounds like you're where you should...

    Woody, this sounds like you're where you should be on suction. But keep in mind that airflow is the real goal with this system.

    Of course, the real test is whether it will pull the 25' tape...
  20. Replies
    64
    Views
    13,968

    Excellent reply from Chris Parks. Trust what he...

    Excellent reply from Chris Parks. Trust what he says.
  21. Replies
    64
    Views
    13,968

    Woody, it is not slipping. You are correct. The...

    Woody, it is not slipping. You are correct. The connection Clear Vue supplies for joining the impeller to the motor shaft is bullet proof.
  22. Replies
    6
    Views
    1,021

    Another +1 for the Jet JDP-17. We have it here in...

    Another +1 for the Jet JDP-17. We have it here in our community workshop and it's an absolute champ. We purchased it after a member's son told us of having it in his shop for over 3 years with...
  23. Replies
    64
    Views
    13,968

    Your plenum setup should not be a problem. I used...

    Your plenum setup should not be a problem. I used a plenum set up with my CV1800 in my basement shop because I didn't have enough ceiling height. Worked just fine. And, as you've no doubt seen, many...
  24. Replies
    64
    Views
    13,968

    Woody, there is no reason to do this. These...

    Woody, there is no reason to do this. These joints are tight and taping the joint at the motor plate will make it a real pain to disassemble the unit should you ever want to do that. But not a...
  25. Replies
    64
    Views
    13,968

    Clear Vue has tried to clear up the confusion...

    Clear Vue has tried to clear up the confusion over the 15" vs. 16" impellers and the 6" vs 8" intakes by moving all the model numbers to the rated CFM of the unit. That is:

    CV1450 - 6" intake with...
Results 1 to 25 of 115
Page 1 of 5 1 2 3 4