Search:

Type: Posts; User: Mark Sipes; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    6
    Views
    658

    Purchased a Tire Depth Gage (7528) Digital...

    Purchased a Tire Depth Gage (7528) Digital Micrometer. Filed the tip to Knife edge and can measure 0.000 - 0.950 " or mm
  2. Replies
    7
    Views
    878

    American Acrylic 5 x5x1 Part # A331 and...

    American Acrylic 5 x5x1 Part # A331 and several more http://www.americanacrylicaward.com/

    .
  3. Replies
    8
    Views
    1,109

    What State ..... Texas?? Bamboo Coasters......

    What State ..... Texas??


    Bamboo Coasters...

    Cut Acrylic

    need to define "can't pay a lot"

    Do you own a laser to customize/fabricate products.
  4. Kev , Tropar sells lots of 40 plate...

    Kev ,


    Tropar sells lots of 40 plate Perpetuals

    .
  5. Pamela, Here is a list of suppliers I use. ...

    Pamela,

    Here is a list of suppliers I use.


    MarcoAwardsGroup.com ( just purchased Freeman)

    JDSindustries.com

    Trophyparts.com (formely PDU)
  6. Replies
    10
    Views
    1,619

    Depending on the location you will have a rent,...

    Depending on the location you will have a rent, electrical, phone/internet , etc payment you did not have yesterday. If you have a customer base that will support the added expense that's great. If...
  7. Replies
    19
    Views
    3,397

    When you say manual test with software.... Does...

    When you say manual test with software.... Does that mean you are pushing buttons to make it move (Hardware) or telling the machine to cut vector without raster and it moves in both axis?

    Mark
  8. Replies
    19
    Views
    3,397

    Is there a reverse or Stamp feature in your...

    Is there a reverse or Stamp feature in your software??? that will reverse the image as if you were engraving on the back of an acrylic or name plate so to read right from the front...
  9. Replies
    9
    Views
    1,540

    Glad you are working to get the machine up and...

    Glad you are working to get the machine up and running again. Keep us involved on your success.

    .
  10. Replies
    9
    Views
    1,540

    Your card just have a cover over the top of the...

    Your card just have a cover over the top of the card. With power off Just pull the two lower cards and switch them. Then reboot and see if the x works and the y does not. If so it is the card, it's...
  11. Source for Melamine Sheet in White/Black

    Any one have a source for Melamine Resin Sheet in White with black core. Have a job that specs this material in .125" thickness.

    I see it in Germany at Eckart but nothing state-side



    Thanks
  12. Replies
    3
    Views
    1,156

    Dome on Top .

    Dome on Top



    .
  13. I am running JC 6.2.3 with Driver 5.15 , Corel 16...

    I am running JC 6.2.3 with Driver 5.15 , Corel 16 and Xp and have never had a file transfer problem...... I have had the job stop in the middle with an error for signal loss, but that is because I...
  14. Replies
    21
    Views
    3,024

    I have both a laser and rotary engravers and...

    I have both a laser and rotary engravers and sublimation. On most days all three processes are used to support industrial customers. I think you need to define your use of the term "industrial" .......
  15. I have gone VOIP so the internet is vital to my...

    I have gone VOIP so the internet is vital to my continued success......... Trifica E-mail/Web Site/Phone. Even Cell phone is ground power based. Without 120v at the plug I am useless...........
  16. Replies
    10
    Views
    1,543

    A Diamond is an easy one. Go to Special...

    A Diamond is an easy one. Go to Special Characters - ZafDingbats and find a diamond shape and drag it onto your;) page...



    .
  17. Replies
    3
    Views
    969

    Try this one.... ...

    Try this one....


    https://www.myfonts.com/fonts/hihretrofonts/rundgotisch/rundgotisch/

    .
  18. Replies
    8
    Views
    1,651

    Confused..... Needed to cut a ring 2.5" deep into...

    Confused..... Needed to cut a ring 2.5" deep into a base holder, but the bowl hold down will work with a 1/4" rod/nut.

    Should have told us is was a standard silver bowl.. I was invisioning a...
  19. Replies
    9
    Views
    1,540

    Appears you are describing problems ranging from...

    Appears you are describing problems ranging from key pad buttons not making good contact to wires, sockets and plugs broken or burnt. The pins and sockets need to have good fitting contact or...
  20. Replies
    9
    Views
    1,540

    Do you feel brave. Since both the Table and...

    Do you feel brave. Since both the Table and Cylindrical are not work we can initially eliminate the cables and motors to the x-axis.......

    1. With the power off I need you to remove the...
  21. Replies
    11
    Views
    2,222

    SO what would one charge for a box of 500? .

    SO what would one charge for a box of 500?


    .
  22. Replies
    2
    Views
    864

    Font Assistance

    What the Font could not help with this font . Any ideas .. Thanks
  23. Replies
    15
    Views
    2,681

    Based on the list of Exhibitors that will be...

    Based on the list of Exhibitors that will be attending I would go to Denver. The SGIA looks to be oriented towards the Printing markets, heavy into ink.


    Why are you purchasing a laser??? ...
  24. Sounds like the machine and computer used to have...

    Sounds like the machine and computer used to have a friendly relationship. What changed. Anti Virus update? Win 7 update Defender..MacFender... Works some time......... Cold Boot of computer and...
  25. Replies
    17
    Views
    3,326

    Residential or Commercial ?....... Length of...

    Residential or Commercial ?....... Length of run to outside ?..... recommended CFM at laser table? ..........

    I'm in a commercial area and I exhaust right out the machine thru the wall to the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4