Search:

Type: Posts; User: Steve Jenkins; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. There might be a chain tensioner on it. It looks...

    There might be a chain tensioner on it. It looks like a piece of heavy gauge wire bent to slide on the chain and held in place with a small bolt.
  2. Replies
    15
    Views
    654

    Similar to Prashun. Two sawhorses with furniture...

    Similar to Prashun. Two sawhorses with furniture pads. Completely finish the bottom then slide it to the side so one edge is near the center of both sawhorses. Rock it up on edge and while holding it...
  3. Replies
    81
    Views
    5,679

    Only thing I can think of to save time is an hour...

    Only thing I can think of to save time is an hour glass. ��
  4. Replies
    32
    Views
    2,329

    Looking good in the shop. Enjoy

    Looking good in the shop. Enjoy
  5. Replies
    127
    Views
    7,218

    Sticky: Add me to the list

    Add me to the list
  6. Replies
    21
    Views
    1,880

    Looks great Jim. A super high gloss finish is...

    Looks great Jim. A super high gloss finish is pretty satisfying to do
  7. Replies
    16
    Views
    1,187

    I don’t know, it seems pretty succinct to me.��

    I don’t know, it seems pretty succinct to me.��
  8. Replies
    6
    Views
    477

    You can get mdf 1/8” or how about using plastic...

    You can get mdf 1/8” or how about using plastic laminate
  9. Replies
    11
    Views
    429

    If your drawer fronts are inset rather than...

    If your drawer fronts are inset rather than overlay you need to deduct the thickness of the fronts from the cabinet depth.
  10. Worked 1/2 days (due to heat) cutting on a downed...

    Worked 1/2 days (due to heat) cutting on a downed pecan tree. Almost finished. Know anyone that can use a 4 diameter trunk?
  11. If it needs to be that private you might consider...

    If it needs to be that private you might consider board and batten.
  12. My shaper has a sliding table similar to that....

    My shaper has a sliding table similar to that. It’s a Gomad made in Poland. Not as fancy as the Martin in that the table doesn’t pivot or fold down but you can raise it up and slide it over to the...
  13. Replies
    1
    Views
    436

    Pecan log

    Anyone near Dallas TX that can handle a 48 diameter pecan log?414530
  14. Replies
    8
    Views
    493

    I don’t use waterborne so don’t know if there is...

    I don’t use waterborne so don’t know if there is a comparable product. I sprayed several coats black primer/surfacer which has a much higher solids content than regular primer then high gloss clear...
  15. I agree with Joe. If you’re looking at a single ...

    I agree with Joe. If you’re looking at a single tier there isn’t much if any advantage over a good home made rack. The panel flattener would be a big advantage though.
  16. Replies
    12
    Views
    863

    Check with D&R saw in Dallas on Harry Hines just...

    Check with D&R saw in Dallas on Harry Hines just north of Walnut Hill Ln
  17. Replies
    28
    Views
    1,597

    I thought that baseball on tv was the most boring...

    I thought that baseball on tv was the most boring thing imaginable until I went to a mlb game
  18. Replies
    6
    Views
    562

    You can make your own pods using melamine covered...

    You can make your own pods using melamine covered particle board and closed cell foam weatherstripping. Seal the edges of the board with glue and make them any shape and size.
  19. Replies
    17
    Views
    1,457

    I use plum creek mdf for paint grade. It is a bit...

    I use plum creek mdf for paint grade. It is a bit denser and the face finish is harder
  20. Replies
    18
    Views
    669

    Wood loses moisture faster from end grain so with...

    Wood loses moisture faster from end grain so with that section being only 2” long (grain wise) it’s probably shrinking faster than the main panel
  21. Replies
    20
    Views
    1,231

    I agree with Jamie. My sliding compound is used...

    I agree with Jamie. My sliding compound is used for cutting scraps to fireplace length
  22. Replies
    4
    Views
    714

    Thanks again

    Thanks again
  23. Replies
    4
    Views
    714

    Thanks David I’ll give him your info. I...

    Thanks David I’ll give him your info. I appreciate it
  24. Replies
    4
    Views
    714

    Fusion 360

    My brother has an X Carve using fusion 360 and is having difficulty with an operation. I know nothing but am wondering if there is someone willing to communicate with him directly. Thanks
  25. Replies
    2
    Views
    516

    Appreciate the offer Bill but I’m pretty much...

    Appreciate the offer Bill but I’m pretty much without transportation so I’m afraid I’ll have to pass.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4