Search:

Type: Posts; User: Jim Becker; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 2.07 seconds.

  1. Don, did you contact the folks that make Gorilla...

    Don, did you contact the folks that make Gorilla adhesive products directly to see if they can point you to a US supplier for the product you want?
  2. The thing is...a lot of what we buy in materials...

    The thing is...a lot of what we buy in materials are metric underneath, but remarked in inches for the convenience of the retail trade. Plywood is a very good example. It's been metric for a very...
  3. This is a VERY subjective thing. There are folks...

    This is a VERY subjective thing. There are folks who waive silver crosses at the idea of using metric and there are those like myself that have dived into it as fully as possible. I started using...
  4. Replies
    4
    Views
    133

    Your general plan is sound, IMHO. If there's no...

    Your general plan is sound, IMHO. If there's no requirement to keep "actual" garage type doors, consider your alternatives. One roll-up can be convenient, but a wall of doors isn't the best choice...
  5. Completion photos for this build. I have a little...

    Completion photos for this build. I have a little more minor intonation work to complete, but this one is done.

    436705 436706 436707. 436708 436709
  6. Replies
    48
    Views
    5,898

    Finally got a couple of outside photos of this...

    Finally got a couple of outside photos of this build...

    436703 436704
  7. Replies
    1
    Views
    116

    That's a wonderful shot to capture to remember...

    That's a wonderful shot to capture to remember this, Lee!
  8. In this photo, you can see the connection for my...

    In this photo, you can see the connection for my saw...5" to the 120mm port on the saw with a wye to 3" to the blade guard branched off the 6" main. Both ports have independent blast gates. Honestly...
  9. Replies
    8
    Views
    263

    Mike, if I needed income from my part time...

    Mike, if I needed income from my part time woodworking business to live, I'd be seriously concerned right now. My best customers are small makers, themselves, and their customers are tenuous, too. So...
  10. Replies
    6
    Views
    587

    https://sgepwq.sn.files.1drv.com/y4mybTci9KE1XVU6z...

    https://sgepwq.sn.files.1drv.com/y4mybTci9KE1XVU6zXuO1TAQtTSOp0F4TQqf06k4jbzEs9CdVQV5pWN0ukS_n-wjIGBl-YG5nNhC0I6-nLl4Ea1DISKvldjmWaF78vHW35fU1z_LijAeM0LYrV2XFYex5rYhXObOakTEn1MbXbuc1LudHyfT3EinkvRNNcC...
  11. Replies
    6
    Views
    587

    This is a steal and if I actually had a use for...

    This is a steal and if I actually had a use for that format of sander, it would already be on its way to my shop...
  12. While our daughters were in their "more...

    While our daughters were in their "more impressionable" years, I moved to using OpenDNS for filtering of sites because of inconsistencies with using the router for filtering and used password...
  13. Replies
    9
    Views
    587

    Thank you, Mike. That's the replacement floor I...

    Thank you, Mike. That's the replacement floor I installed a number of years ago...largely for safety reasons, but it does look good. The floor in that room when we bought the house had been "sanded...
  14. You'd only be cutting between the two existing...

    You'd only be cutting between the two existing cuts to remove the big piece of waste and it would leave only a little to deal with via a sharp chisel. You can remove it with a bandsaw but that will...
  15. Remove waste initially with a drill and depth...

    Remove waste initially with a drill and depth stop. Make a template that you can use with a bearing guided router bit to clean the edges...it can be stuck down with the painter's tape and CA glue...
  16. Replies
    20
    Views
    591

    My experience is similar. I think that a lot of...

    My experience is similar. I think that a lot of this misrouting is because of damaged or incorrect bar codes or difficult to read zip codes on hand addressed items. This stuff is all sorted and...
  17. When I look at this photo: ...

    When I look at this photo:

    https://sawmillcreek.org/attachment.php?attachmentid=436631&d=1594491040

    I see a short cut between the two kerfs. That's why I and Derek are saying fretsaw. There's...
  18. Replies
    2
    Views
    118

    BLO by itself is completely compatible with an...

    BLO by itself is completely compatible with an oil based varnish or "poly" if it's cured. Many even use BLO as a base ingredient before they are "cooked". If it's a BLO and wax finish, however, the...
  19. He's only needing to do the short waste cut based...

    He's only needing to do the short waste cut based on the photo which shouldn't be a problem for a fret saw and would leave less to clean up than doing the angles and nibble dance with a band...
  20. Replies
    9
    Views
    587

    Thanks, David. She does appreciate the work I do...

    Thanks, David. She does appreciate the work I do for her and for the house.
    -----

    So this "flat thing" project is done. Not an exciting project, not a complicated project, not even any jointery....
  21. First thing that came to my mind was a fretsaw,...

    First thing that came to my mind was a fretsaw, too. You have the room with the kerfs to use one if my eyes are not deceiving me and can then clean them at the visible edges with very sharp chisels.
  22. Replies
    30
    Views
    1,133

    You deleted your most previous recent post prior...

    You deleted your most previous recent post prior the new one, Jon. :)

    Torsion boxes are great for assembly including clamping if they are setup well for the need.
  23. That's about the distance I'm at spraying with a...

    That's about the distance I'm at spraying with a pretty generous fan on the flat piece of mahogany in my current project thread. It's an "art form" to be consistent with this, too!
  24. Little dabs of hot melt for temporary. Hide glue...

    Little dabs of hot melt for temporary. Hide glue for "more permanent" that can still be taken apart if required.
  25. Replies
    9
    Views
    411

    The DXF file defines the project and can provide...

    The DXF file defines the project and can provide the vectors (the type of lines that are turned into CNC instructions) to the maker. But that's just the start of the journey. Those drawings need to...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4