Search:

Type: Posts; User: Bill Wyko; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.28 seconds.

  1. No, my band saw's capacity isn't big enough.

    No, my band saw's capacity isn't big enough.
  2. A smaller one has made a person dizzy but it was...

    A smaller one has made a person dizzy but it was due to their own condition.
  3. I was cutting a board about 1.5 inches thick and...

    I was cutting a board about 1.5 inches thick and cutting off about 1/8th of an inch. The board had a recess I didn't notice and the blade came through the side.On a regular saw, I would have lost...
  4. Thanks very much.

    Thanks very much.
  5. It weighs over 200 lbs, better be a strong wall.

    It weighs over 200 lbs, better be a strong wall.
  6. I use a lot of reference marks, originally tried...

    I use a lot of reference marks, originally tried to just line them up but it was too confusing.
  7. Not meant to be funny, I've taken the ends off 2...

    Not meant to be funny, I've taken the ends off 2 fingers myself and put my saw stop to the test 2 weeks ago. I've had numerous people say they would cut themselves so I'm curious what the liability...
  8. A rough count puts it at over 11,000 pieces.

    A rough count puts it at over 11,000 pieces.
  9. If you cut your fingers off, would I be responsible. LOL

    So, would I be responsible if you chopped off your fingers on my cutting board? Inquiring minds want to know. This is a whole hog cutting board for Rec Tec grills.
  10. Hi Jim, it only works if you don't have a whole...

    Hi Jim, it only works if you don't have a whole hog on it.
  11. End grain cutting board with thousands of pieces

    Been working on this since October, what a mind bender. I'm working on the border now.
  12. Replies
    8
    Views
    2,434

    Everything is end grain including the border so...

    Everything is end grain including the border so expansion shouldn't be an issue. It is essential to keep them oiled.
  13. Replies
    8
    Views
    2,434

    Another dizzying design cutting board.

    I'm at it again, Another 3D end grain cutting board. 416342
  14. Thanks, these actually are endgrain and extremely...

    Thanks, these actually are endgrain and extremely stable. Takes a ton of wood to make them.
  15. Replies
    15
    Views
    3,948

    If you want to get creative, you could cut it...

    If you want to get creative, you could cut it into strips about 1.25 thick, turn them up 90 degrees, glue them back together and make it an end grain cutting board. That way you almost never see a...
  16. You should see what it takes to keep everything...

    You should see what it takes to keep everything lined up, that will bang your eyeballs into each other.
  17. I use masking tape to hold everything while I...

    I use masking tape to hold everything while I carefully apply pressure with the clamps.
  18. What do you think is the best rolling base for heavy tools?

    I have a Baileigh 25" surface sander on the way and I need a rolling base for it. it measures 41 x 12.5 at the base. It weighs around 600 lbs. I would like it to fit the base, not one size fits all...
  19. A couple cutting boards to get sucked into.

    So I'm not back to full capacity yet but I've made time to make a few cutting boards recently. Please enjoy.
  20. Replies
    11
    Views
    1,860

    Eventually I want to turn a platter using one of...

    Eventually I want to turn a platter using one of these on my lathe.
  21. Replies
    11
    Views
    1,860

    Thanks everyone, the border is Cocobola, hard...

    Thanks everyone, the border is Cocobola, hard Maple and Jatoba. Been using it for a few weeks now and not a trace of a mark anywhere.
  22. Replies
    11
    Views
    1,860

    Dizzying cutting board

    So I've taken up cutting boards as a new way to express myself. Over 400 pieces, made of Jatoba, hard Maple and Cocobola. Please enjoy.
  23. Replies
    3
    Views
    881

    hey had a video of exactly what I want to do,...

    hey had a video of exactly what I want to do, thanks again.
  24. Replies
    3
    Views
    881

    Thanks very much, going there now.

    Thanks very much, going there now.
  25. Replies
    3
    Views
    881

    Traditional finish on a Morris chair

    I plan on building some Morris style furniture, what would be the traditional style finish and the best method for application?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4