Search:

Type: Posts; User: Jay Norton; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    31
    Views
    2,372

    What is the condition of the tires on the saw? ...

    What is the condition of the tires on the saw?

    I saw big vibration improvements on a 14” Delta clone I had after replacing the old rubber tires with urethane tires.
  2. Replies
    4
    Views
    882

    Jim/John, Thanks for the feedback. Honestly,...

    Jim/John,

    Thanks for the feedback. Honestly, it was what I expected, don’t worry about the manufacturer specs, just go by the actual product in hand. Just trying to learn all I can .. ;)
    ...
  3. Replies
    4
    Views
    882

    Viscosity conversion

    Is there a reliable source for a viscosity conversion chart/calculator out there?

    I am entering the spray finish world. I bought a quart each of Target Coatings EM2000 & EM6000 in satin.
    ...
  4. Replies
    61
    Views
    6,604

    Aaron, I agree the Cosman micro-bevels could...

    Aaron,

    I agree the Cosman micro-bevels could be challenging, especially since they are likely done without a jig.

    The Charlesworth ruler trick may be easier, as the new user can fairly easily...
  5. Replies
    6
    Views
    1,046

    Echoing what Jim said… Here is a link to an...

    Echoing what Jim said…

    Here is a link to an old Charles Neil video about trace coating to enhance figured wood.

    https://youtu.be/mjTSIiUiEOI?si=ksiDrXjPO672rnOQ
  6. Thread: Sandpaper

    by Jay Norton
    Replies
    22
    Views
    1,867

    I haven’t really compared their prices to...

    I haven’t really compared their prices to anywhere else, but I like their Rhynogrip hook & loop discs

    https://www.industrialabrasives.com/
  7. Replies
    24
    Views
    5,388

    Karl, The spacers I used are 1/2” OD x 1”...

    Karl,

    The spacers I used are 1/2” OD x 1” long. Bolts are 3/8”.

    I am happy so far with the solution and the position.

    I opted to keep the rail flush with the right edge of the table as I...
  8. Replies
    68
    Views
    8,241

    Well said. Agree 100%

    Well said. Agree 100%
  9. Replies
    68
    Views
    8,241

    I have purchased a couple large machines at...

    I have purchased a couple large machines at Woodcraft. Both were shipped free to the store (I ordered in store). I picked both up at the store. They loaded them into my truck.
  10. https://www.industrialabrasives.com/58-hole-assort...

    https://www.industrialabrasives.com/58-hole-assortment-rhynogrip-hook-loop-discs-01950-p-1386.html?zenid=h03n3104r1mpuj7smh0n7mtgj3
  11. Replies
    1
    Views
    748

    Chisel markings ??

    Does anyone recognize the markings on this chisel? Curious of the origin/manufacturer…

    I have 3 with similar markings. This is the only visible lettering on the chisel.

    505294
  12. Replies
    26
    Views
    2,477

    I was questioning if drilling the hole would...

    I was questioning if drilling the hole would distort the metal.
  13. Replies
    26
    Views
    2,477

    He recommended hanging as an alternative to...

    He recommended hanging as an alternative to horizontal (properly supported)
  14. Replies
    26
    Views
    2,477

    I gave Starrett a call and spoke to a tech. He...

    I gave Starrett a call and spoke to a tech. He said drilling a hole in the end would not affect the accuracy.
  15. Replies
    26
    Views
    2,477

    Agree, hanging is a good storage method. My...

    Agree, hanging is a good storage method.

    My question is does drilling a hole in a steel/aluminum straight edge have any affect on accuracy?
  16. Replies
    13
    Views
    1,322

    I have had good luck with Krud Kutter (the red...

    I have had good luck with Krud Kutter (the red bottle) cleaner/degreaser
  17. Replies
    26
    Views
    2,477

    Straight edge hanging hole

    Has anyone drilled a hole in their straight edge for hanging/storage?

    Did it affect the accuracy?
  18. Replies
    17
    Views
    9,176

    I put a coat on the underside/no show surfaces...

    I put a coat on the underside/no show surfaces today.

    All surfaces primed with 2 coats Zinsser BIN, lightly sanded with 320

    SW Pro Classic acrylic satin
    thinned ~5% with water (1.5 oz in 1 qt...
  19. Replies
    33
    Views
    3,957

    Which Laguna did you buy? Interested if anyone...

    Which Laguna did you buy? Interested if anyone has tried the Quadtec 8”/1.75 HP 110v
  20. Replies
    17
    Views
    9,176

    Small world. I went to college at Alfred State. ...

    Small world. I went to college at Alfred State. I live in PA now, but get up to the Alfred area quite often to hunt.
  21. Replies
    17
    Views
    9,176

    John, Thanks! What general part of Western NY...

    John, Thanks!

    What general part of Western NY are you located?

    I grew up in Steuben County.

    Jay
  22. Replies
    17
    Views
    9,176

    Greg, I designed it. Here are the rough...

    Greg,

    I designed it. Here are the rough dimensions.
    The height is ~22”. The top is 14 3/4” x 42”. Shelves have 7 1/2” between them.

    Jay
  23. Replies
    17
    Views
    9,176

    I tried a sample piece with 2 coats spray...

    I tried a sample piece with 2 coats spray Polycrylic. It definitely darkened the 2 coats of white primer under it. Polycrylic on left side

    499515

    I am leaning towards using ProClassic without...
  24. Replies
    17
    Views
    9,176

    Jeff, Is Minwax Polycrylic considered “water...

    Jeff,

    Is Minwax Polycrylic considered “water white”? It is advertised as non-yellowing. I believe I recall it being milky white in the can.
  25. Replies
    17
    Views
    9,176

    Jeff & John, thanks for the info, very helpful

    Jeff & John, thanks for the info, very helpful
Results 1 to 25 of 53
Page 1 of 3 1 2 3