Search:

Type: Posts; User: Keith Westfall; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    36
    Views
    1,445

    Left shirt pocket - all the time...

    Left shirt pocket - all the time...
  2. Replies
    6
    Views
    531

    Thanks! Searched for the chair, never thought to...

    Thanks! Searched for the chair, never thought to search for the plans... :)
  3. Replies
    6
    Views
    531

    On Amazon it's $475!! Can do a lot of BB for that...

    On Amazon it's $475!! Can do a lot of BB for that kind of money :D

    Pretty easy design, if I can get the slope and angles ok so it won't tip over!!

    The CNC will do a quick job on the cutout.
  4. Replies
    6
    Views
    531

    Stokke Tripp Trapp High Chair

    Not sure where to ask this.
    Has anyone ever made one or something similar?

    Thanks - Granddaughter request...


    415885
  5. Replies
    22
    Views
    2,238

    Poll: Red as well. Old tool boxes - seemed you could...

    Red as well. Old tool boxes - seemed you could have any colour you wanted as long as it was red, or maybe grey...
  6. Put it on an uneven floor - then what happens?...

    Put it on an uneven floor - then what happens? Can't see it myself...

    What the $$ value?
  7. Replies
    13
    Views
    910

    Wouldn't it be neat to be able to say that??...

    Wouldn't it be neat to be able to say that?? Quietly, as a fact.

    Thanks for sharing.
  8. Replies
    8
    Views
    1,037

    I did the same - hope it helps. They are not that...

    I did the same - hope it helps. They are not that bad - as I thought they might be...
  9. Painting a Front Entrance Metal Door

    Anyone have any tricks, suggestions etc on painting a metal exterior door? I've done some googling and get it all:


    Latext paint
    Oil base
    Paint with primer all in one
    Laying flat
    Hanging...
  10. I had to hang 5 kids portraits in a double row (3...

    I had to hang 5 kids portraits in a double row (3 & 2) for my daughter, and not wanting to 'mark the wall' I ran 2 vertical stripes of masking tape on each end of the wall and measured down to...
  11. Replies
    146
    Views
    19,469

    When you go into your local coffee shop, beer...

    When you go into your local coffee shop, beer joint, restaurant, etc., do you ask for their income and profit statement to see if they are charging too much??? Of course not. Does it matter if any of...
  12. Replies
    146
    Views
    19,469

    Hard to tell Chris, what you really want or...

    Hard to tell Chris, what you really want or expect. Let's make it a free forum, pay contributors for their content and then share it with everyone?

    A lot (most/many of us) contribute because we...
  13. Saw a guy demo a way... Get a plug (could be...

    Saw a guy demo a way...

    Get a plug (could be turned out of wood) the right size (if you need it bigger) and then heat the plastic and push in the plug, causing it to form to the new size. May...
  14. Replies
    33
    Views
    2,183

    Cut a 45* and then cut those 2 points again....

    Cut a 45* and then cut those 2 points again. You'll be getting pretty close - nothing a disc sander couldn't fix...
  15. Marc, You come asking questions and for advice,...

    Marc,
    You come asking questions and for advice, but when it is given, you state that you have done it the way your doing it and it works. Then just do it that way.

    Many of us use the 2 runner...
  16. Replies
    31
    Views
    2,120

    I have one in an old Hitachi that sticks once in...

    I have one in an old Hitachi that sticks once in a while. With the nut off, I take a small brass drift and hit up (or down when installed in CNC) lightly around the end, rotating the shaft a bit each...
  17. Replies
    19
    Views
    1,525

    I've put black model paint in it and don't seem...

    I've put black model paint in it and don't seem to have any problems with that. Doesn't take very much, depending on how much you're filling.
    A few drops go a long ways.
  18. Not a Bell, it's a 3 bladed machine. Probably one...

    Not a Bell, it's a 3 bladed machine. Probably one of the Airbus series...

    Bells are 2 or 4 bladed.
  19. Replies
    20
    Views
    2,008

    I believe that when you want to empty it, you...

    I believe that when you want to empty it, you just the front up a bit and it rides up over the snow. Then a slight tip down and a pull back leaves the snow behind.

    You never lift, just the handle...
  20. Replies
    41
    Views
    3,987

    What do you do when your in shop, turn them off....

    What do you do when your in shop, turn them off. or remove them.

    I don't wear mine in the shop, they will turn off or mute themselves while wearing my ear muffs. I still have enough hearing I...
  21. Replies
    41
    Views
    3,987

    I got mine just over a year ago at Costco. Senior...

    I got mine just over a year ago at Costco. Senior discount (Alberta $800 off the top) and walked out at around $1200 for the pair. They're fairly small, silver colour, and had them for a bit before...
  22. Replies
    22
    Views
    1,681

    I have and like the caliper that John showed and...

    I have and like the caliper that John showed and would love to get another...



    Price:
    $29.95 on Amazon.com


    ]CDN$ 100.06 on Amazon.ca
  23. Replies
    5
    Views
    631

    Thanks for that! Always like Clint. Not sure if...

    Thanks for that! Always like Clint. Not sure if it's about me getting old, or doing things so I don't get old...

    Hopefully the latter :)
  24. Replies
    46
    Views
    4,156

    My dad used a slide rule, even taught me a bit on...

    My dad used a slide rule, even taught me a bit on it a looonnnngggggg time ago. For many many years he carried a small 4" circular one in his pocket. He could figure almost anything on it. I think I...
  25. Replies
    7
    Views
    1,045

    Did one for a friend for their little dog......

    Did one for a friend for their little dog...
    400900400901

    Cherry with some walnut trim. Top comes off to be glued on later.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4