Search:

Type: Posts; User: Lee Schierer; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.95 seconds.

  1. Replies
    1
    Views
    139

    Very nice an Heirloom for sure. The top is...

    Very nice an Heirloom for sure. The top is really a nice piece of wood.
  2. Replies
    30
    Views
    757

    Here is a link to the specifications for a Galaxy...

    Here is a link to the specifications for a Galaxy Z Flip2 5Gb

    I casually looked at one a while back at the AT&T store and wondered how long before the folding screen fails.
  3. Replies
    14
    Views
    721

    The Freud Glueline rip blade has flat top teeth...

    The Freud Glueline rip blade has flat top teeth and TCG and is reasonably priced. Half of the teeth are flat top half are TCG. It gives a nice flat bottom kerf and a smooth sidewall cut.
    481561
  4. Replies
    4
    Views
    420

    Make a filler out of maple that will fit in the...

    Make a filler out of maple that will fit in the wide kerf. Glue that filler in place and make your new cut once the glue cures completely.
  5. Replies
    7
    Views
    447

    You are listed as a Member, if this is not...

    You are listed as a Member, if this is not correct, please contact Keith Outten.

    Only contributors can send personal messages through the system. Becoming a contributor costs a minimum of $6...
  6. Replies
    11
    Views
    588

    Really nice job. I like the color and the nice...

    Really nice job. I like the color and the nice finish.
  7. Replies
    14
    Views
    594

    All have been deleted without opening them......

    All have been deleted without opening them......
  8. Replies
    17
    Views
    1,960

    The donate button does show up in full site mode...

    The donate button does show up in full site mode on tablets and phones.
  9. I converted a closet into a pantry for my wife. ...

    I converted a closet into a pantry for my wife. I used full extension soft close slides rated for 100 pounds.
    481348481346 481347
    The shelves are made with poplar frame, red oak front panel and...
  10. Just be sure to apply your glue to both sides of...

    Just be sure to apply your glue to both sides of the joint.

    You need to make or buy a clamping set up like this. You don't need to fill in all four pieces, you can glue up just two at a time,...
  11. Thread: bee trap

    by Lee Schierer
    Replies
    10
    Views
    680

    Nothing other than size and it is up in a tree.

    Nothing other than size and it is up in a tree.
  12. Replies
    8
    Views
    728

    I had suggested a cloth covering but it was...

    I had suggested a cloth covering but it was rejected.

    Just a note those soft fiber bulletin boards start to fail if you place too many tacks or push pins in the same area.
  13. Replies
    14
    Views
    594

    Annoying spam

    For the past week we've been receiving supposed emails from McAfee saying our subscription is about to expire. Sometimes we get two or three per day. Today we started getting the same bogus notices...
  14. Thread: Firefox

    by Lee Schierer
    Replies
    12
    Views
    592

    I'm running Firefox 101.0.1 on windows 11 with no...

    I'm running Firefox 101.0.1 on windows 11 with no issues.
  15. Replies
    8
    Views
    728

    Lessons learned working with cork

    I was asked to make a couple of bulletin boards to go on the back of some doors in the church welcome center. The deign called for two 18 x 24 framed cork boards. I was able to order the 3/8" x 24"...
  16. Replies
    20
    Views
    836

    That is a nice set up and the price is good. Be...

    That is a nice set up and the price is good. Be careful measuring from the sides of the teeth, because most are have a relief grind on the sides which can lead to errors.

    Switch you gauge to the...
  17. Replies
    1
    Views
    327

    I would say you were successful....

    I would say you were successful....
  18. Replies
    20
    Views
    836

    Are you measuring off the side of a tooth or the...

    Are you measuring off the side of a tooth or the blade plate when you make these parallel measurements.

    I put a mark on a point close to a tooth with a magic marker. I rotate that point from...
  19. Replies
    20
    Views
    836

    From your photo, it looks like the back teeth of...

    From your photo, it looks like the back teeth of the blade is dragging on your wood based on those curved grooves on the cut edge.
    481144
    I would check the alignment of the blade to the miter slot...
  20. Replies
    5
    Views
    390

    They look like house finches.

    They look like house finches.
  21. From photo #4, it appears that the corners are...

    From photo #4, it appears that the corners are made from 3 pieces. There is a vertical and a horizontal. The third piece is cut from a wider piece of wood and then attached to the top rail and side...
  22. Philip is correct, only contributors can post and...

    Philip is correct, only contributors can post and view photos. Support SawmillCreek with your contributions. For a minimum of $6, you can have contributor status for a calendar year, which includes:...
  23. Replies
    2,181
    Views
    314,607

    Sticky: I had a sign just like that in my office for a...

    I had a sign just like that in my office for a while. Funny no one ever asked which case was relevant to them.
  24. Replies
    5
    Views
    539

    I don't think there is a limit. The software...

    I don't think there is a limit. The software will resize the photos before posting them. It just takes longer with larger file sizes.
  25. You can also use a shop vac to get glue into...

    You can also use a shop vac to get glue into cracks. Apply a generous amount of glue to the top of the crack on one side of the board. Turn on the shop vac and hold the nozzle close to the crack on...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4