Search:

Type: Posts; User: Don Jarvie; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    18
    Views
    505

    If your looking to resaw look for saws with large...

    If your looking to resaw look for saws with large resaw capabilities. While older saws are bigger they don’t have the resaw capacity of the newer ones. The new 14 inch saws from Laguna, Rikon, etc...
  2. Replies
    7
    Views
    316

    Have you made sure the headstock pulley set...

    Have you made sure the headstock pulley set screws are tight and any other set screws tight? This could explain the back and forth. The motor hangs on the headstock so it could move it. This happened...
  3. The ones at Home Depot fit and work fine.

    The ones at Home Depot fit and work fine.
  4. Check the Bay. I found my duet door there.

    Check the Bay. I found my duet door there.
  5. Replies
    72
    Views
    5,192

    Unless the bolts are broken they can be reused....

    Unless the bolts are broken they can be reused. HF sells a good buffer cheap and put a couple of wire wheels on it, one course and one fine. Take the planer completely apart, clean, repaint and put...
  6. Replies
    10
    Views
    788

    If you haven’t joined OWWM join. There’s a ton of...

    If you haven’t joined OWWM join. There’s a ton of restoration information there. You can get the dust cover and motor cover on EBay. I got a 74 at an auction with a 3 phase motor and swapped it out...
  7. Surplus Center.com has a great variety of belts...

    Surplus Center.com has a great variety of belts in pretty much all sizes.
  8. Replies
    31
    Views
    3,011

    I’ve tried all kinds of pencils but the best one...

    I’ve tried all kinds of pencils but the best one is still the Papermate mechanical yellow pencil.
  9. Replies
    4
    Views
    1,059

    These go in the holes on the comparator rear...

    These go in the holes on the comparator rear bracket. They are used to hold a spindle you were trying to duplicate See pages 16-17 of the manual. If you don’t have the manual just google Powermatic...
  10. Replies
    11
    Views
    1,097

    I would have to say that’s a pretty good price...

    I would have to say that’s a pretty good price considering the helical head would cost a 1/3 to 1/2 of the price. Since you are familiar with complete teardowns if it’s just needs a good clean up and...
  11. Just my opinion... 1. Plywood, MDF and...

    Just my opinion...

    1. Plywood, MDF and particle board aren’t the strongest to support shelves
    2. Paint. You can putty all of the holes, etc. it’s a closet
    3. The HD and Lowe’s poplar or birch...
  12. They do make chauk in colors. Where are you going...

    They do make chauk in colors. Where are you going to chauk? If it’s between the slats the wood may expand and contract which could crack the chauk.
  13. Replies
    19
    Views
    1,710

    Surplus Center has pulleys for a reasonable price.

    Surplus Center has pulleys for a reasonable price.
  14. Is plywood an option? You can get a plywood in...

    Is plywood an option? You can get a plywood in most native woods.
  15. Replies
    13
    Views
    1,309

    1/2 ply will work just as well. It will probably...

    1/2 ply will work just as well. It will probably cost as much as the OSB and 1/8.
  16. Replies
    11
    Views
    1,013

    50 bucks. Nice score.

    50 bucks. Nice score.
  17. Replies
    6
    Views
    789

    I would recommend you try to make the garage work...

    I would recommend you try to make the garage work and use the basement for wood and supply storage. Over time it will be a pain to keep going back and forth.

    Start searching the web for ideas and...
  18. Replies
    15
    Views
    1,641

    As Randy mentioned pine is not a great wood for...

    As Randy mentioned pine is not a great wood for outdoor use. Cedar, team and mahogany will do better outside.
  19. Surplus Center sells belts in any size and width...

    Surplus Center sells belts in any size and width you need. I get my belts there and have had no issues.
  20. Replies
    5
    Views
    527

    Check Surplus Center. They list bushings at 18 mm...

    Check Surplus Center. They list bushings at 18 mm that can be inserted in a pulley. I used a bushing for my jointer and it works fine.
  21. In my shop I built an assembly table attached to...

    In my shop I built an assembly table attached to my TS with the router wing. I didn’t want anything hanging or had room under the floor so I ran 2 DC lines, one for the TS and one for the router. I...
  22. Replies
    13
    Views
    893

    Lee Valley

    Lee Valley
  23. Replies
    16
    Views
    1,505

    Jim described what I did as the comments on the...

    Jim described what I did as the comments on the moisture issues and impact on your body are spot on. There is a product called drycore which can be laid down directly on the concrete since it’s...
  24. Replies
    16
    Views
    1,257

    I’ve done a similar thing and the power goes into...

    I’ve done a similar thing and the power goes into the switch and then run a line to the outlet. It would be just like running a light switch instead of a light it’s an outlet. Only draw back is I...
  25. Replies
    7
    Views
    1,123

    What a great job. I love the feature ring design.

    What a great job. I love the feature ring design.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4