Search:

Type: Posts; User: Lee Schierer; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.42 seconds; generated 24 minute(s) ago.

  1. Replies
    19
    Views
    698

    I know that when cutting 45 degree bevels on...

    I know that when cutting 45 degree bevels on pieces to be joined together I end up with no visible gaps in the joints when putting four pieces together to make a square.

    To set an angle, I place...
  2. Replies
    19
    Views
    698

    So how does your machinist square measure a 35.5...

    So how does your machinist square measure a 35.5 degree bevel angle that I needed to cut for a project I did this past weekend on my table saw? My Beall gauge did it as I changed the blade angle...
  3. Sort of a false sense of security since air borne...

    Sort of a false sense of security since air borne particles could easily go over, around or through the opening for exchanging cash or credit cards....
  4. Replies
    4
    Views
    387

    You can edit the title, text and photos in "Go...

    You can edit the title, text and photos in "Go Advanced" mode for 24 hours after your original post......I did this one for you.
  5. Replies
    12
    Views
    251

    You can buy a 50 foot 30 Amp RV power cord that...

    You can buy a 50 foot 30 Amp RV power cord that is ready made. They are stranded.
  6. Replies
    2
    Views
    172

    It's good that you have a fix. I also use Fire...

    It's good that you have a fix. I also use Fire Fox 74.0.1 (64-bit) and have no issues viewing posts or photos. Since SMC doesn't do tracking I have disabled the Enhanced Tracking Protection for the...
  7. Replies
    3
    Views
    162

    Practical project

    About 40 years ago, I converted a hole in the floor in our bathroom closet, made by the previous owner, into a laundry chute complete with its own door. I also made a suspended enclosure in the...
  8. My experience with velcro is that the grip gets...

    My experience with velcro is that the grip gets weaker over repeated opening and closing. That would apply to the base plate of your sander not new pads from your inventory.
  9. Replies
    19
    Views
    698

    I have the Beall Tilt Box digital gauge and it...

    I have the Beall Tilt Box digital gauge and it remains accurate after more than 15 years. I uses a 9 volt battery which lasts a really long time. It is advertised as having an accuracy of .2...
  10. Replies
    17
    Views
    694

    I use the miter slot on my bandsaw relatively...

    I use the miter slot on my bandsaw relatively often.

    I have a circle cutting jig that uses the miter slot to position the jig properly on the table. Blade drift is controlled by adjusting the...
  11. On thin pieces that aren't thick enough to ride...

    On thin pieces that aren't thick enough to ride against the bearing when routed horizontally, I use the fence on my router table to hold the piece in a vertical position while I run the edge across...
  12. Replies
    25
    Views
    814

    I've been getting robo calls for months...

    I've been getting robo calls for months identified as spam, yet the phone company puts them through anyway.
  13. Replies
    17
    Views
    611

    You could make a nice hot house or two with those.

    You could make a nice hot house or two with those.
  14. Replies
    11
    Views
    460

    As others have noted holding the cabinet on the...

    As others have noted holding the cabinet on the wall is dependent on the fasteners used to attach the cleats to the wall and to the back of the cabinet. Then load bearing capacity comes down to the...
  15. Replies
    11
    Views
    428

    I found through experience that using a crosscut ...

    I found through experience that using a crosscut or combination blade when cutting tenon cheeks resulted in tapered cheeks. When I switched to a dedicated rip blade things got noticeably better.
  16. Replies
    17
    Views
    668

    You can edit your posts, including the title for...

    You can edit your posts, including the title for 24 hours after posting. To edit the title use the "Go advanced" button on the edit page in full site mode.
  17. Replies
    6
    Views
    221

    source for trigger sprayer

    I been looking for a source for a few trigger spray heads similar to the one in the photo. the longer pickup is what I am looking for. 429504
  18. Replies
    6
    Views
    272

    Pretty much any of the wood fillers that dry hard...

    Pretty much any of the wood fillers that dry hard and can be sanded can be used if the surface will always be painted.
  19. Replies
    9
    Views
    356

    It appears that the Ryobi BT3000 has a sliding...

    It appears that the Ryobi BT3000 has a sliding table attachment.
    429397
  20. Replies
    11
    Views
    470

    You could fill the cut with PC-7. Let it set up...

    You could fill the cut with PC-7. Let it set up for at least 24 hours and then recut the slot with your table saw.
  21. Replies
    10
    Views
    414

    It works pretty well for depth. Try it on some...

    It works pretty well for depth. Try it on some scrap first.
  22. I heat/cool my shop with the house HVAC system. ...

    I heat/cool my shop with the house HVAC system. I have two air returns in my shop. I equipped each of them with merv 10 filters. I can find no trace of dust in the air returns back into the house....
  23. Replies
    10
    Views
    412

    We are still a couple of weeks away from grass...

    We are still a couple of weeks away from grass mowing. The yard is much too wet for our lawn tractor.
  24. Ken you have way too much time on your...

    Ken you have way too much time on your hands.....:rolleyes:
  25. Replies
    10
    Views
    414

    You can cut the dados safely on a table saw. ...

    You can cut the dados safely on a table saw.

    First you set the width and depth of cut with your dado blade.

    Once you are satisfied lower the blade using the raise lower handle noting the...
Results 1 to 25 of 497
Page 1 of 20 1 2 3 4