Search:

Type: Posts; User: Bill Dufour; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds; generated 41 minute(s) ago.

  1. Replies
    37
    Views
    917

    For a gfci outlet I prefer to have the gfci...

    For a gfci outlet I prefer to have the gfci inside and daisy chain to a outside outlet. It is a little less convenient but the gfci stays nice and dry and does not fail from moisture. I have had two...
  2. Replies
    5
    Views
    272

    I have had to adjust the distance to lock out far...

    I have had to adjust the distance to lock out far away stuff. But I still occasionally search without the blinders on and it is interesting to see such distant ads.
    Bil lD
  3. Replies
    16
    Views
    546

    The way it works is that as soon as the virus...

    The way it works is that as soon as the virus gets into the wet body tissue the outer layer breaks down and the RNA strand is free to move into a likely looking cell and take over from the existing...
  4. Replies
    24
    Views
    812

    Three HD's within 5 miles of my home. The one in...

    Three HD's within 5 miles of my home. The one in the nicer part of town has limits on customers. The other two do not.
    Bil lD
  5. Replies
    37
    Views
    917

    Watch craiglist for used breaker panels, all the...

    Watch craiglist for used breaker panels, all the same make, I would have at least one sub panel on the opposite end of the shop from the main service panel. Also watch for heavy cable at least #8...
  6. recommnended blade tension is 15,000-20,000psi. ...

    recommnended blade tension is 15,000-20,000psi. A 3/4 by 0.032 blade needs about 800 pounds of force. I am not sure if this is 800 0r 1,600 pounds on the saw. I think they mean 800.
    For a...
  7. I think in a home shop just a normal cable clamp...

    I think in a home shop just a normal cable clamp will be fine. the fancy braided wire cable grippers are for industry where the cords are being pulled and moved all the time. I assume the cord will...
  8. Replies
    5
    Views
    272

    OT: Craigs list real estate question

    I have been looking for a retirement home for several years to get ideas on pricing and location in California. Only looking near the coast were the weather is better but prices are higher.
    I...
  9. Replies
    16
    Views
    546

    Alcohol above 85% will not bother the virus if it...

    Alcohol above 85% will not bother the virus if it is like other viruses. The high concentration alcohol will cause it to go into a defense mode and it can "live" in pure alcohol for several years. ...
  10. Replies
    18
    Views
    507

    many bandsaws become scrap when they are moved...

    many bandsaws become scrap when they are moved with the table attached. It falls into something or is grabbed and the trunnions break. Consider metal saws not just wood saws. If the FPM is correct...
  11. They are low speed so most any make is fine. ...

    They are low speed so most any make is fine. Depending on how hard it is to remove them I have no problem with ebay no name bearings. common size under $2.00 each. Name brand about $10. for for...
  12. Replies
    18
    Views
    507

    Older big saws tend to have poor blade guides. ...

    Older big saws tend to have poor blade guides. Often stackable metal plates which are missing so you can only run one blade width. Make sure there are modern blades guides to fit your saw before...
  13. Replies
    18
    Views
    541

    expanded metal mesh

    expanded metal mesh
  14. Too small at a four foot cube but, the fed ex...

    Too small at a four foot cube but, the fed ex flat rate box is a good deal for under 1,400 pounds. A tablesaw would fit but not the fence rails. 130-290 shipping cost. I believe that price...
  15. Never been the 30 miles to see the store but the...

    Never been the 30 miles to see the store but the adds look good.
    Located in Tracy Ca, near Stockton.

    http://www.professionalmachinery.com/default.asp

    Bill D
  16. surprised to see the hole at the worst possible...

    surprised to see the hole at the worst possible location and not a speaker box.
    Bil lD.
  17. Replies
    18
    Views
    541

    Shingles? Bill D

    Shingles?
    Bill D
  18. Replies
    18
    Views
    541

    Fiberglass, flame resistant cloth, wicker,...

    Fiberglass, flame resistant cloth, wicker, leather. metal screen. panel beater could make something for you. lath and plaster
    Bil lD.
  19. Mills and Drills Are you sure they are balls and not a dowel? ...

    Are you sure they are balls and not a dowel? They may be floating in the holes and held in by grease for assembly so they do not fall out. I would think about drilling them out and replacing with...
  20. Replies
    42
    Views
    1,832

    Easy way to stay safe is to bag the purchases...

    Easy way to stay safe is to bag the purchases into cold stuff that needs to come in and go into the fridge. Wash your hands and take a break. Everything else can sit in the car for 3 days then be...
  21. Replies
    6
    Views
    221

    Would heat shrink tube work? may have to put a...

    Would heat shrink tube work? may have to put a spring inside so it does not collapse.
    Bil lD
  22. Replies
    8
    Views
    401

    Clean so no oil or grease on either part that...

    Clean so no oil or grease on either part that touches. Open chuck so jaws do not show, place taper in chuck and set chuck nose down on bench. wack tang end with a rubber hammer one time.
    Be...
  23. Replies
    117
    Views
    5,502

    Wiping down with duct tape should pull those...

    Wiping down with duct tape should pull those nasty covid 19 cooties right off your skin in no time flat. Just not sure how to throw the used tape away without getting it stuck everywhere and...
  24. Anything with marine in the name is about 10...

    Anything with marine in the name is about 10 times the cost of normal stuff. look at what builders use to get power to new home job sites from undeground power lines or mobile home power set ups. ...
  25. Replies
    17
    Views
    611

    Cut down for sandpaper plate for sharpening ...

    Cut down for sandpaper plate for sharpening chisels etc.
Results 1 to 25 of 497
Page 1 of 20 1 2 3 4