Search:

Type: Posts; User: bill ward; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    2,626

    Thanks for your worthwhile information. Gives me...

    Thanks for your worthwhile information. Gives me details to think about.
  2. Replies
    10
    Views
    2,626

    Good points. Thanks for your comments

    Good points. Thanks for your comments
  3. Replies
    10
    Views
    2,626

    Thanks for taking the time to respond to my post....

    Thanks for taking the time to respond to my post. You’ve given me some things to think about.
  4. Replies
    10
    Views
    2,626

    Prevent warping

    What is the best way to minimumiz warping in a wooden sign made from quarter sawn white oak hung outdoors? I have my own ideas but am always looking for good advice. Thanks
  5. Thread: Link belt

    by bill ward
    Replies
    17
    Views
    1,927

    Link belt

    For those of you having trouble with a vibrating table faw, I've gone through every adjustment with precision instruments and adjusted everything to o.001" on my Delta contractors table saw with...
  6. What ever takes, right?

    What ever takes, right?
  7. Thanks for the comment. Is your 14 & 16 needing...

    Thanks for the comment. Is your 14 & 16 needing restoration? I've had great time restoring mine. Crowning the new rubber tires is the last thing needing to be done. Looking forward to using it.
  8. Thanks. Do you have a WT bandsaw?

    Thanks. Do you have a WT bandsaw?
  9. Crowning the the top tire of an old 14" walker Turner bandsaw

    I've been restoring an old Walker Turner bandsaw over the past few months and the last thing remaining is crowning the rubber tires. The bottom tire was easy because it's driven by the motor;...
  10. Replies
    10
    Views
    2,229

    I haven't had any problem with any part of the...

    I haven't had any problem with any part of the restoration; however, I don't feel comfortable crowning the tires... Installing tires isn't a problem. I was hoping to find a place that can install and...
  11. Replies
    10
    Views
    2,229

    Thanks. I'll get with OWWM. I haven't had any...

    Thanks. I'll get with OWWM. I haven't had any problem with any part of the restoration; however, I don't feel comfortable crowning the tires... Installing tires isn't a problem. I was hoping to find...
  12. Replies
    10
    Views
    2,229

    I haven't had any problem with any part of the...

    I haven't had any problem with any part of the restoration; however, I don't feel comfortable crowning the tires... Installing tires isn't a problem. I was hoping to find a place that can install and...
  13. Replies
    10
    Views
    2,229

    Walker Turner bandsaw rebuild

    I've about completed my restoration of a 1940s Walker Turner bandsaw. Does anyone know where I can get new tires installed as well as new bearings for the shafts?
  14. Do you need a spring or a shorter length blade?

    Do you need a spring or a shorter length blade?
  15. Replies
    7
    Views
    2,259

    Thought I'd send you a picture of the bearings I...

    Thought I'd send you a picture of the bearings I got on Ebay. They have the grove like the original but don't have the oil hole in the shaft. Don't see that as a problem.273220
  16. Replies
    7
    Views
    2,259

    Thanks. I agree with your thinking, sealed...

    Thanks. I agree with your thinking, sealed bearings make a lot of sense. I'll give accurate bearings a call today to discuss. Thanks again. Bill
  17. Replies
    7
    Views
    2,259

    Good information. Thhanks

    Good information. Thhanks
  18. Replies
    7
    Views
    2,259

    Thanks Terry. The only bearings needing to be...

    Thanks Terry. The only bearings needing to be replaced are the ones on the upper and lower wheels. I found blade thrust bearings on EBay for $44 if you ever need any. Go to...
  19. Replies
    7
    Views
    2,259

    Walker Turner 14" bandsaw rebuild

    Though I'd completed my 14" WT band saw but I think I have a bad bearing. The saw seems to run fine until it starts to slow down when I turn it off, then there's a short vibration which I hadn't...
  20. Replies
    6
    Views
    1,781

    I recently made a mail box out of PVC and simply...

    I recently made a mail box out of PVC and simply did a light sanding and wiped it down with Acetone and painted it with a good grade of latex paint. So far so good.
    272258
  21. Replies
    4
    Views
    1,404

    One possible solution would be to line the inside...

    One possible solution would be to line the inside of the box with a thin (color?) let''s say white, plexiglas. Use silicone to adhere glass to all sides including the top & bottom and then put the...
  22. Replies
    5
    Views
    1,537

    To determine the blade length, assuming both...

    To determine the blade length, assuming both wheels have the same diameter, simply determine the circumference of a wheel and add that to twice the distance between the wheel's center points. Be sure...
  23. Replies
    24
    Views
    16,911

    Sorry for butting in but I think the size is...

    Sorry for butting in but I think the size is referring to the file size. Right click on your picture, select properties. Look at "size"... if it's larger than 1.9 MB it more than likely will not...
  24. Replies
    11
    Views
    1,269

    Why cut a hole in the door? Can you mount a...

    Why cut a hole in the door? Can you mount a shop-vac hose under the table at the lower guide assembly?
  25. Amazing. Thanks

    Amazing. Thanks
Results 1 to 25 of 42
Page 1 of 2 1 2