Search:

oh, yes, I forget to mention, the blade is 90 to the table, on the back and on the side.

I am not sure how to adjust the column...messed around a little bit and cannot find a way.

I recently bought a new rikon 10-3061 bandsaw and set it up according to the manual and various youtube video guides, have not done any real projects yet, but I just noticed that while everything...

for the velocity 20" floor fans, will it be better off placing it in the back of the garage, instead of at the garage door?

I do woodworking in garage while the two garage doors open, is there any good fan that I can use to help blow the dust out through the doors?

Right now I have got a costco pedestal fan, but it...

Just providing an update, I bought a new blade and now it cuts straight pretty well.

Thanks everyone for the great input, I appreciate it!

okay, here is another update,


Changing the blade position does not change much(if anything), i was putting the the deepest part of the gullet with the center of the top wheel, and moving the...

I watched this video and have followed all the steps and the result is still the same.

In order to rule out the possible alignment issue, I on purposely "rotated" the table as far as it could go...

Sorry I am a bandsaw noob, so I already need a new blade although the current one is brand new? 😂

My first bandsaw, a new rikon 10-3061, set it up according to the manual and various youtube tutorials such as Alex Snodgrass's method (align the blade, tension the blade, thrust bearings and side...

I am making 3 long floating shelves, (7.5 feet), the top, bottom, and middle section all are 45 miter, and with table saw, not matter how careful I tried, the end result of the long bevel board look...

Thanks guys, Ground Contact Pressure-Treated Plywood is the PWF you guys refered, correct?

I have got a very small concrete landing area (about 4ft x 4ft) which needs to covered by subfloor so laminated floor can be installed.

Can I just use some leftover loctite pl300 to glue a piece...

oh boy, i might just put back the old carpet ....:eek:

hmmm, the issue is "not" upper and lower stairs have difference riser heights.

No matter what I do, either the last step of the upper stairs OR the first step of the bottom stairs will not be the...

My basement staircase looks like this, a flight of stairs, then landing area, then another set of stairs,

465048


The whole thing was covered with carpet before, and I am removing the carpet...

As promised, here is the update, the stairs now are not squeaky at all now after using framing anchors. I used 6 anchors and they work pretty well. :)

Thanks everyone for the great inputs! I am...

Thanks guys, I will start with the framing anchors first, will be heading to the box store to get those in a little bit.

Will provide updates soon.

The space under the stair is a basement closet, (these are stairs going down to the basement).

I think at this point, we can tell the problem is the moving middle section between the two skirt...

Okay, hopefully the last question, please see the photo below, I was planning to screw the stringers to the stub through "A", but it seems that the A in the photo is actually skirtboard and the two...

Here are two photos, it seems that the fit between stringers and wall is pretty tight, I see no gaps I need to shim. If folks think the GRK rss rugged structure screws #10 x 3-1/8 is good, I will...

Hi guys, I have some GRK rss rugged structure screws #10 x 3-1/8.

Will that be sufficient to fix the stringers to the studs? Or I better go to HD to get the Ledger Board Fastener?

Thanks

Thanks, will probably do this first and see how it goes.

Thanks all for the inputs!

This morning me and my wife did some more tests on the stairs, we found out that when we rock on one step, we can feel the other treads are rubbing slightly against the...

Thanks, is there a good way to cut the already glued tread now on both ends without making it look like someone bites the edges off? :D

I tested on one tread and put in 10 screws last night, does not seem to help, maybe I need to do them all, :(