Search:

Type: Posts; User: George Yetka; Keyword(s):

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    460

    Overarm sold Blade guard available

    Overarm sold

    Blade guard available
  2. Replies
    20
    Views
    11,015

    General Metalworking steel does get work hardened. Milwaukee has...

    steel does get work hardened.

    Milwaukee has some new bandsaw blades i bought in a pinch this summer. the box said it was good for thick steel but the teeth looked agressive. and they were...
  3. Replies
    24
    Views
    1,087

    the festool stuff while expensive is very good...

    the festool stuff while expensive is very good with adjustability. the only other routers i have are palm and one in a lift.
  4. Replies
    13
    Views
    395

    https://www.amazon.com/Black-Swan-Mfg-Co-04085/dp/...

    https://www.amazon.com/Black-Swan-Mfg-Co-04085/dp/B008KOIQEA/ref=sr_1_1?dchild=1&keywords=black+swan+no+hub&qid=1610396857&sr=8-1

    but mentioned that when i thought it was cast. Its like a super...
  5. Replies
    5
    Views
    268

    https://www.youtube.com/watch?v=ESSU7EmT-cE ...

    https://www.youtube.com/watch?v=ESSU7EmT-cE
    ...
  6. Replies
    13
    Views
    395

    Slowly open cleanout before taking the clamp off...

    Slowly open cleanout before taking the clamp off to make sure its not full.

    Rubber will get hard and brittle and shrink over time. I would replace the rubber and make sure both ends of the...
  7. Replies
    1
    Views
    460

    WTS Sawstop Overhead dust collection

    $165 Shipped for the 2" overarm dust collection setup. was used on 52" but I think it works on all table sizes


    $100 Blade guard with dust port
    449190
    I rarely used these and now have the 4" ....
  8. Replies
    15
    Views
    596

    I like them use them for all plywood and longer...

    I like them use them for all plywood and longer rip cuts. Only regret is I lost my shelf
  9. Replies
    43
    Views
    1,712

    Do not lift by the jointer bed they are pretty...

    Do not lift by the jointer bed they are pretty adamant about that.
  10. Replies
    21
    Views
    656

    Avoid culligan. Im a mechanical contractor so i...

    Avoid culligan. Im a mechanical contractor so i got a deal on their gold equipment. Ive replaced alot of parts in 5 years. Go with fleck. Backwash can go into indirect drain into septic or sewer but...
  11. Replies
    26
    Views
    1,068

    https://jessem.com/collections/router-table-packag...

    https://jessem.com/collections/router-table-packages/products/ultimate-excel-ii-package I have this one without the casters. It is a nice table Added a couple drawers and a box for dust under table....
  12. Replies
    17
    Views
    787

    Woodpecker can also be had from other suppliers...

    Woodpecker can also be had from other suppliers at the same price with free shipping. They're quality tools that are expensive but only relatively. there's others out there that are much more...
  13. Replies
    49
    Views
    3,572

    Anything big enough to make cutting board gets...

    Anything big enough to make cutting board gets made into a cutting board
    Anything big enough to make into coaster gets made into coaster
    Anything too short to make a coaster goes in the bottle...
  14. you can remove that plastic piece too and bolt...

    you can remove that plastic piece too and bolt plywood using those 4 studs shown
  15. I took that one apart and bolted a 5 gallon...

    I took that one apart and bolted a 5 gallon bucket to it with sorting trays to sort brass for reloading. It worked well for my purposes. There are 3 or 4 bolts bolted thorough a bracket into the...
  16. I would say make a couple frames out of something...

    I would say make a couple frames out of something else and put these in them.
  17. Replies
    17
    Views
    787

    I agree shipping can get expensive(boxes,packing...

    I agree shipping can get expensive(boxes,packing material,shipping rate itself, plus labor to pack item) But I have stopped a purchase with them because of shipping. I wait for the woodshows to buy...
  18. I have a piece I bought a few years ago. Sliced...

    I have a piece I bought a few years ago. Sliced off a small piece to throw in a cutting board, and after letting glue dry took it out of clamps and board fell in half like I forgot the glue. Think I...
  19. Replies
    32
    Views
    1,162

    Ive been meaning to upgrade to the floating. I...

    Ive been meaning to upgrade to the floating. I rarely had the guard on the saw so it didnt work that well. I put it on for large plywood sessions. and it works well
  20. Replies
    35
    Views
    1,734

    the Midi has 10%less cfm. Not sure if thats...

    the Midi has 10%less cfm. Not sure if thats critical for you, or anyone. I run my 26 like 75%power So the midi would work
  21. Replies
    6
    Views
    581

    If your getting rid of domestic dust(no walnut) I...

    If your getting rid of domestic dust(no walnut) I think alot of farms will take it. I alternate with trash can and dumping in the woods. Usually dump every other 40 gallon
  22. Replies
    40
    Views
    2,521

    Time to print, quality of print, and size of...

    Time to print, quality of print, and size of print can be your only restrictions. I have a cheeper machine and have batched out alot. (mainly desiccant containers, cups for drill bits for a press...
  23. Replies
    12
    Views
    595

    Dont know if its the beard but I couldnt get the...

    Dont know if its the beard but I couldnt get the rzr mask to work for me fogged eyepro pretty bad. worked well while sanding when i could take off eypro though. I switched to the elipse and although...
  24. Replies
    40
    Views
    2,521

    I got the best woodworking gift of all, time in...

    I got the best woodworking gift of all, time in the garage away from kids to do so. On a day of my choosing. And my mother in law doubled down by giving me an additional day saying she would take...
  25. Replies
    12
    Views
    624

    How about some ratcheting knobs. Similar to...

    How about some ratcheting knobs.

    Similar to this but in the apropriate thread...
Results 1 to 25 of 217
Page 1 of 9 1 2 3 4