Search:

Type: Posts; User: Steve Kang; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    16
    Views
    2,254

    Not sure if I can get a bottle jack under the...

    Not sure if I can get a bottle jack under the short side stretchers, don't think I have the clearance. Perhaps a low profile floor jack could do it but I don't want to buy a tool for a one time job...
  2. Replies
    16
    Views
    2,254

    Roubo on the move

    Hi everyone, looking to make some layout adjustments to my workshop which requires moving my workbench. Any good ideas on how to best tackle moving a roubo?
  3. I just use tea lights, pull the wicks out and...

    I just use tea lights, pull the wicks out and they're good to go.
  4. Replies
    3
    Views
    662

    Hey Andrew, good find! I missed that section,...

    Hey Andrew, good find! I missed that section, I'll shoot them an email to see what they have to say.
  5. Replies
    3
    Views
    662

    Knife pivot hinges - load capacity?

    Hello, looking for a bit of advice on knife pivot hinges (krenov style?). I'm planning on using them as part of a tool cabinet build but I'm concerned about sag and weight limits. Neither brusso or...
  6. Replies
    36
    Views
    7,065

    I think you're probably dead on at 40lbs. I don't...

    I think you're probably dead on at 40lbs. I don't mind the weight since I bring it up relatively infrequently.
  7. Replies
    36
    Views
    7,065

    Mine lives under my bench, where it's...

    Mine lives under my bench, where it's accumulating a layer of dust, shavings and offcuts. 445020
  8. Replies
    6
    Views
    1,394

    Did LN discontinue this plane? Not seeing it...

    Did LN discontinue this plane? Not seeing it listed on their website...
  9. Replies
    16
    Views
    5,052

    Hi Charles, I had the same concern when building...

    Hi Charles, I had the same concern when building my roubo. There was something about having a portion of the board unsupported while planing which didn't sit right with me. I can tell you in actual...
  10. Stu, if you're reading this, thank you!

    Stu, if you're reading this, thank you!
  11. Replies
    7
    Views
    1,680

    Are you sure the mix ratio was supposed to be...

    Are you sure the mix ratio was supposed to be 1:1? I recently used the ecopoxy liquid plastic product and the ratio I used was 2:1. I believe at some point they changed their guidance on the ratio...
  12. Replies
    21
    Views
    4,246

    Great tip Edwin, thanks for sharing. If one were...

    Great tip Edwin, thanks for sharing. If one were to by a 2nd blade for 8/4 hardwoods, would your recommend the 28 or 14 tooth?
  13. Has anyone tried Furniture and Cabinetmaking?...

    Has anyone tried Furniture and Cabinetmaking? It's a UK mag which focuses on fine furniture making.
  14. Replies
    8
    Views
    1,978

    Honestly, it's just because working out ducting...

    Honestly, it's just because working out ducting is a headache and I'm starting to loath doing it. A few hours searching for sewer drain pipe was a waste of time, another few hours looking into 24g...
  15. Replies
    8
    Views
    1,978

    Hi Glen, I know it's verboten around these parts...

    Hi Glen, I know it's verboten around these parts but I'm going to use smooth bore flex hose to create the sweeps. I feel they'll be very comparable to the double 45 method.
  16. Replies
    8
    Views
    1,978

    Thanks guys, picking up material today and should...

    Thanks guys, picking up material today and should have this sorted by the end of the weekend.

    @Stevo, I though about it but i'd lose headroom as it's a basement shop.
  17. Replies
    8
    Views
    1,978

    Basic DC Drop Question

    Hi All,

    Looking for a little advice on ducting diameter. My DC is a laguna P|flux2 which should be rated for 2hp, the impeller is 14.5". I'm planning on running a 6" main line across the left...
  18. Replies
    30
    Views
    12,566

    I own a full set and all of them are perfect, no...

    I own a full set and all of them are perfect, no notable defects. Early on I did have an issue with the no.3 and no.4. For the no.3 they had included the wrong chipbreaker and adjustment knob, which...
  19. I use a one-way multigauge with a dial indicator,...

    I use a one-way multigauge with a dial indicator, but you could rig up something similar out of wood if you have an indicator kicking around....
  20. Replies
    13
    Views
    1,574

    I'll take the bait. What's wrong with Harvey...

    I'll take the bait. What's wrong with Harvey Industries?
  21. Replies
    13
    Views
    1,574

    Nice find, this is great news!

    Nice find, this is great news!
  22. Are you sure you want a combo j/p machine? I'd go...

    Are you sure you want a combo j/p machine? I'd go with separates if you're putting together a student workshop. If someone's using the machine for planing, then they're also tying up the jointer......
  23. Replies
    9
    Views
    1,932

    Good call, that's an option.

    Good call, that's an option.
  24. They don't sell bandsaw's and there are...

    They don't sell bandsaw's and there are exclusions for use on sawstops and festool.
  25. Replies
    9
    Views
    1,932

    Sucking dust

    Fellas, looking for a little straight talk on dust collection piping. I know that solid smooth bore piping with a minimum diameter of 6" is preferred but how much would I really be giving up by going...
Results 1 to 25 of 87
Page 1 of 4 1 2 3 4