Search:

Type: Posts; User: Doug Bowman; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    11
    Views
    9,895

    My lumber cost for western red cedar ran about...

    My lumber cost for western red cedar ran about $50 a chair - I used 5/4 tight knot cedar from my local supplier and bought fence slats for the 4/4 stuff - i purchased enough for 2 chairs and have...
  2. Replies
    12
    Views
    1,457

    Cut with the band saw and clean up the face with...

    Cut with the band saw and clean up the face with the jointer.
  3. Replies
    34
    Views
    6,889

    This^^^^^ It is also liberating to know that I...

    This^^^^^
    It is also liberating to know that I can go use hand tools for that occasional board that is too wide for the machine
  4. Have you pulled the belt and run the motor by...

    Have you pulled the belt and run the motor by itself? And while you are at it spin the lower wheel. I would initially suspect bearings motor or lower wheel
  5. Replies
    26
    Views
    4,127

    Yep if you only have 2 boards I would use my...

    Yep if you only have 2 boards I would use my trusty $25 #5 with a nice camber on the blade - just did it last night more then 2 and I start thinking about getting the lunchbox planer out.
  6. Replies
    22
    Views
    4,554

    yeah 42 F is about when I switch to foul weather...

    yeah 42 F is about when I switch to foul weather shorts
  7. Replies
    11
    Views
    3,992

    I find the noise level of my HF 2 hp dust...

    I find the noise level of my HF 2 hp dust collector to be very tolerable. I would not have guessed from running it that hearing protection would be necessary. Now turn on my shop vac or lunchbox...
  8. Replies
    30
    Views
    4,612

    I think he is lucky he has them all when he gave...

    I think he is lucky he has them all when he gave her a tool bag for her birthday!
  9. Replies
    14
    Views
    2,005

    I know this is the power tool forum, but if I...

    I know this is the power tool forum, but if I only had a little bit of rock (I assume it twisted) i would use a hand plane to remove the high spots - but that does not solve your resaw problem - and...
  10. Replies
    7
    Views
    1,477

    Nothing to add just wanna say that is a great...

    Nothing to add just wanna say that is a great signature line.
  11. Replies
    29
    Views
    8,111

    Thanks Van

    Thanks Van
  12. Replies
    29
    Views
    8,111

    Minor hijack but same topic (same saw)- what...

    Minor hijack but same topic (same saw)- what would you go with for non-carbide and again what width - 3/4 or half?
  13. Replies
    20
    Views
    3,373

    My father did this several times when refinishing...

    My father did this several times when refinishing and restoring furniture. It works
  14. Replies
    2
    Views
    815

    A couple of different techniques come to mind -...

    A couple of different techniques come to mind - you can start on the concave side and work traversing the stock to level the ends to match the middle until you have the concave side flat enough to...
  15. Replies
    16
    Views
    2,365

    I am all for it - always love a good bench thread

    I am all for it - always love a good bench thread
  16. I see the Delta 28-350's come up for sale on...

    I see the Delta 28-350's come up for sale on Craigslist periodically - I was wondering what is the resaw capacity?
  17. i would have brought it as a carry on because I...

    i would have brought it as a carry on because I am afraid they would lose it
  18. Replies
    25
    Views
    4,174

    I keep a non-cambered blade in mine - it is...

    I keep a non-cambered blade in mine - it is primarily used as a shooting plane and a small jointer. I have the LV version
  19. Replies
    19
    Views
    4,798

    And i would agree with you if he was using a...

    And i would agree with you if he was using a filter, however he is venting outside
  20. Replies
    19
    Views
    4,798

    +1 a properly built Thein can eliminate all...

    +1 a properly built Thein can eliminate all visible dust and since you are venting outside that would be my choice.
  21. Replies
    23
    Views
    5,136

    In my previous house I had a lumber rack hung...

    In my previous house I had a lumber rack hung from the ceiling above the garage door. I wish I could do that in my current house but there is no room above the garage door.
  22. Replies
    26
    Views
    7,591

    yep this is what I would do

    yep this is what I would do
  23. Replies
    19
    Views
    21,104

    My choice would be the Thein baffle - you are...

    My choice would be the Thein baffle - you are venting outside and all I would worry about is visible dust which a properly built baffle is very effective at removing.
  24. Replies
    33
    Views
    5,511

    i am a moderately experienced sawyer - I have...

    i am a moderately experienced sawyer - I have relatively successfully sharpened 5 saws - although I have never had to add set to one yet. I have a bishop hand saw 26" 8 ppi I would like to setup for...
  25. Replies
    33
    Views
    5,511

    Stewie, what angles would you recommend for a...

    Stewie,
    what angles would you recommend for a crosscut hand saw that can be dedicated to finishing cuts in very dry hard woods
Results 1 to 25 of 60
Page 1 of 3 1 2 3