Search:

Type: Posts; User: Matt Riegerix; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    1,190

    My experience with the Ohishi stones I purchased...

    My experience with the Ohishi stones I purchased from Lie Nielsen, a 1000, 4000 and 8000 is that they are not true splash and go stones. They need a bit of soaking, they also do gouge easily if you...
  2. Should have waited to become a supporter. 😜

    Should have waited to become a supporter. 😜
  3. Sharp chisel, followed by card scraper.

    Sharp chisel, followed by card scraper.
  4. Thread: Cat Gate

    by Matt Riegerix
    Replies
    9
    Views
    1,782

    Hi Chris, The wood is ponderosa pine, I got...

    Hi Chris,

    The wood is ponderosa pine, I got wet from a local sawmill, air dried it in my backyard.

    I had originally planned on filling in the full asa-no-ha pattern like this smaller grid I...
  5. Thread: Cat Gate

    by Matt Riegerix
    Replies
    9
    Views
    1,782

    Thanks, Unfortunately, a few feet tall...

    Thanks,

    Unfortunately, a few feet tall wouldn't stop these cats.
  6. Thread: Cat Gate

    by Matt Riegerix
    Replies
    9
    Views
    1,782

    Laying out the half lap joints was helped by some...

    Laying out the half lap joints was helped by some clamps.
    508604

    508605

    508606
    508607
    508608
  7. Thread: Cat Gate

    by Matt Riegerix
    Replies
    9
    Views
    1,782

    Cat Gate

    Hello,

    Longtime reader, rare poster. Trying to answer the call for more project posts. We had a problem with our cats causing mischief in our bedrooms, to put it kindly. We wanted to allow airflow...
  8. Replies
    27
    Views
    3,730

    I was lucky enough to have some teak scraps to...

    I was lucky enough to have some teak scraps to laminate into a sharpening bench top. It’s holding up well, though I tend to wipe up excess water when I’m through.
  9. Replies
    6
    Views
    1,367

    Great work. I’ve never experienced tear out with...

    Great work. I’ve never experienced tear out with a scraper, I always use the scraper to fight tear out.
  10. Replies
    31
    Views
    4,754

    The listing says itís made in India, so Iím sure...

    The listing says itís made in India, so Iím sure thereís plenty of profit margin.
  11. Replies
    21
    Views
    3,077

    I'm pretty happy with basic 3m sandpaper. But...

    I'm pretty happy with basic 3m sandpaper. But maybe that's why I avoid sanding.
  12. Replies
    10
    Views
    1,810

    Looks like a deal compared to recent Ebay prices.

    Looks like a deal compared to recent Ebay prices.
  13. Thread: Kumiko

    by Matt Riegerix
    Replies
    19
    Views
    3,755

    Thanks, I had let it slide, I just renewed.

    Thanks, I had let it slide, I just renewed.
  14. Thread: Kumiko

    by Matt Riegerix
    Replies
    19
    Views
    3,755

    That one is about 12" square. Thanks for the kind...

    That one is about 12" square. Thanks for the kind words. Here's another one.
    https://www.instagram.com/p/CJBhtNfg60Y/?utm_medium=copy_link
  15. Thread: Kumiko

    by Matt Riegerix
    Replies
    19
    Views
    3,755

    I'm having trouble uploading pictures, but here's...

    I'm having trouble uploading pictures, but here's a link to an instagram post of one of my kumiko panels I made following matt Kenneys instructions.
    ...
  16. Thread: Kumiko

    by Matt Riegerix
    Replies
    19
    Views
    3,755

    I like Matt Kenneys book on kumiko.

    I like Matt Kenneys book on kumiko.
  17. I found I had to widen the slot on a veritas...

    I found I had to widen the slot on a veritas pmv11 blade for it to fit properly in my LN bronze #4.
  18. Replies
    24
    Views
    3,941

    Love the resourcefulness. Looking good.

    Love the resourcefulness. Looking good.
  19. Replies
    12
    Views
    1,373

    Hi, The cheap side clamp jigs tend to have a...

    Hi,

    The cheap side clamp jigs tend to have a hard time holding chisels well, i've read you can file the jaws to hold them better but havent had luck with that. I recently purchased the Lie Nielsen...
  20. Replies
    18
    Views
    2,077

    Neat project, you dont see finger joints not on...

    Neat project, you dont see finger joints not on the table saw to often.
  21. Replies
    12
    Views
    2,032

    Great solution, looks nice.

    Great solution, looks nice.
  22. Replies
    22
    Views
    3,540

    Supply is definaetly an issue. Anecdotally in my...

    Supply is definaetly an issue. Anecdotally in my case demand has risen a lot too, I've been seperated more often from the fully equipped woodshop I work at and doing more handwork in my garage, and...
  23. Replies
    30
    Views
    3,366

    Congratulations! Its great to have a marketing...

    Congratulations! Its great to have a marketing team like that.
  24. Replies
    105
    Views
    22,628

    Pretty exciting stuff. Anyone have...

    Pretty exciting stuff. Anyone have recommendations for a buffing wheel for a Rikon 80-805 slow speed grinder?
  25. Replies
    105
    Views
    22,628

    At least you still got your plane irons to use on...

    At least you still got your plane irons to use on stones. Are there any downsides?
Results 1 to 25 of 34
Page 1 of 2 1 2