Search:

Type: Posts; User: Prashun Patel; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.66 seconds.

  1. What material? Im partial to Waterlox original...

    What material? Im partial to Waterlox original sealer finish. Rock solid and easy to apply. If you are spraying, target and general finishes make some good choices: Em8000cv and enduro clear...
  2. Replies
    53
    Views
    1,846

    Its an expensive purchase for people but mass...

    Its an expensive purchase for people but mass produced. That means it has to have broad appeal.
  3. Replies
    15
    Views
    615

    Mark, the difference in color appears to me to be...

    Mark, the difference in color appears to me to be from sapwood/heartwood contrast. Any other difference won't IMHO be noticed.

    Now, whether you LIKE the difference is another story. I do agree...
  4. Replies
    15
    Views
    615

    I think you should post some pictures first. ...

    I think you should post some pictures first.

    I suspect you will be fine just using a darker topcoat like Waterlox (which is a great choice on cherry) or even just using a blonde shellac as a...
  5. Thread: Epifanes

    by Prashun Patel
    Replies
    5
    Views
    295

    Stick with that.

    Stick with that.
  6. I would buy the slider attachment . What a...

    I would buy the slider attachment . What a
    great excuse to upgrade.
  7. I use the wider setting often on large panel glue...

    I use the wider setting often on large panel glue ups where I want flush joint alignment but am relying on the edge to handle the glue.

    On joints that many get stressed in the longitudinal...
  8. Ive used the cmts and have many Amana router...

    Ive used the cmts and have many Amana router bits. Id put the Amanas as about as reliable as Whiteside. I believe in their quality and would be comfortable with the domino bits they make. ...
  9. Replies
    20
    Views
    1,808

    My preference for a drawbore pin that needs to...

    My preference for a drawbore pin that needs to flex would be white oak. The walnut may work fine but white oak is harder. The end grain of the white oak will make a great contrast to cherry.
  10. Replies
    22
    Views
    864

    Forget the chord. The template will work...

    Forget the chord. The template will work regardless of whether it's just as long as the chord or longer.

    Measure 22" on a string and tie it to a nail in your bench. Tie a pencil to the other...
  11. Replies
    22
    Views
    864

    What am I missing? Cut your template longer than...

    What am I missing? Cut your template longer than the finished piece. Cut a whole Semi circle if you wish. Cut your blanks over sized, Bend them in the form and then trim them to size after they...
  12. Replies
    22
    Views
    864

    We will get there. Some dumb questions: Are...

    We will get there.
    Some dumb questions:
    Are your measurements in mm or inches? Unless you have a giant pencil, the radius looks too tight.

    A 22 radius may not appear visually more right...
  13. Replies
    74
    Views
    3,309

    You can always be flatter, sharper, squarer. ...

    You can always be flatter, sharper, squarer.

    But you may be flat, sharp, and square enough.

    Aim for the first but be content with the second.
  14. Replies
    12
    Views
    1,053

    I finished a bath vanity in EM6500 tinted to a...

    I finished a bath vanity in EM6500 tinted to a Benjamin Moore color. His match was perfect.

    IIRC it only comes in one sheen?

    I wanted a flat finish and some more protection, so I topcoated...
  15. Replies
    11
    Views
    965

    Sorry I should have been more clear. It's a...

    Sorry I should have been more clear. It's a friction fit quick connect port on the hose that plugs into the female metal port under my bandsaw table. I have a single-tool set up. The hose is a...
  16. Replies
    7
    Views
    1,020

    You can also shop for cabinet scrapers. These...

    You can also shop for cabinet scrapers. These are thumb savers and can be more versatile than a scraper plane by virtue of a shorter sole.

    Veritas makes one and it appears to have a shorter back...
  17. Replies
    11
    Views
    965

    Bandsaw Dust Port Loose

    My dust collector is a little too powerful for the friction fit hose that I connect to the bandsaw. It forever pops loose.
    I can drill and rig up a cotter pin to lock it in place, but thought I...
  18. Replies
    15
    Views
    1,223

    Different strokes. I would find a second 5000 a...

    Different strokes. I would find a second 5000 a big clunky bother to have in the shop. And they are not cheap. I use an auxiliary plywood fence as the zero clearance backer. It takes only a few...
  19. I like crocs. Hard enough to resist mild drops...

    I like crocs. Hard enough to resist mild drops of tools or wood. Not afraid to get finish drips on it.
  20. Replies
    21
    Views
    1,443

    Well said.

    Well said.
  21. Replies
    15
    Views
    1,223

    I hung a couple j hooks on the wall and it sits...

    I hung a couple j hooks on the wall and it sits there. I have not found a convenient way to mount it to the tablesaw.
  22. Replies
    15
    Views
    1,223

    U can do either.

    U can do either.
  23. I try not to turn it on and off often. If there...

    I try not to turn it on and off often. If there will be more than about 5 mins between tool changes I will shut it off.
  24. Replies
    26
    Views
    2,968

    On the contrary, I find with this style of...

    On the contrary, I find with this style of construction extremely forgiving. Scott, what do you mean by fracturing the seat?
  25. Replies
    11
    Views
    905

    That's serious machinery. I'd get a 3hp cyclone...

    That's serious machinery. I'd get a 3hp cyclone for that equipment. You don't look back. If you have the ability to vent outside, I would. It saves space and hassle.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4