Search:

Type: Posts; User: Eric Schubert; Keyword(s):

Page 1 of 17 1 2 3 4

Search: Search took 0.01 seconds.

  1. Downside to track saws is they're usually quite a...

    Downside to track saws is they're usually quite a bit more expensive than a standard circular saw. In fact, a track saw would cost as much as my table saw. But, if it's something you'll use...
  2. Well, one side of the glue joint cleaned up...

    Well, one side of the glue joint cleaned up really easily. Nice and straight and square. The other side, however, has some really dark streaks that are super hard and it's tough to plane that stuff...
  3. LOL, all good, Mel. I taught a class today, so my...

    LOL, all good, Mel. I taught a class today, so my brain is pretty toasted right now.

    I did get the glue joint ripped open. I don't have a track saw, but I used my circular saw, a finishing blade,...
  4. Thanks, Mel. But, as I mentioned above, this was...

    Thanks, Mel. But, as I mentioned above, this was done by hand. I do not own a jointer, aside from my rehabbed Stanley #7.



    Thanks, Andrew. I'm going to at least rip that one glue seam to start...
  5. Unfortunately, I do not know any other...

    Unfortunately, I do not know any other woodworkers in my area.



    See below for photos of the piece. I was concerned about how much of the seam had a gap, so I took a very thin feeler gauge and...
  6. I'm tempted to rip the seams open again and...

    I'm tempted to rip the seams open again and reglue. However, my table saw is a DeWalt jobsite saw. The DWE7491RS, to be specific. The table is fairly short, the fence is short, and I just use feed...
  7. I'm not sure what I would've done wrong. I...

    I'm not sure what I would've done wrong. I alternated clamps on top and bottom, some facing one direction, some the opposite direction (i.e. some clamps turned 180 degrees compared to other clamps,...
  8. I probably should have mentioned, edges were...

    I probably should have mentioned, edges were jointed with a hand plane after rough jointing on a table saw. I do not own a jointer. I also should have mentioned that these boards are hard maple, in...
  9. How to deal with only partial glue squeeze out?

    I'm working up some large panels for a desk top. It's my first attempt at really making something this large. The panels are 30 x 48 inches (three glue joints) and 30 x 84 inches (two glue joints)....
  10. Thanks, Phil! I'll search out some examples on...

    Thanks, Phil! I'll search out some examples on installing each type. Being my first table, I'm learning a lot about how they're constructed and how tops get attached to allow for movement. Thanks...
  11. Those examples definitely help! Thanks! My...

    Those examples definitely help! Thanks! My bevel was angled more-steeply. Rather than the majority of the bevel being underneath the top, mine has the majority of the bevel on the outer visible...
  12. I'm not sure I'm visualizing what you're...

    I'm not sure I'm visualizing what you're recommending. Any chance you have a link or photo of an example? I'd love to see it.
  13. Thank you for the feedback! It's a little tough...

    Thank you for the feedback! It's a little tough to see, but the top does have a slight undercutting taper to it around the perimeter. I believe it's approximately 25° or so, with the bevel starting...
  14. Interesting. Is the cherry meant to add a thin...

    Interesting. Is the cherry meant to add a thin decorative layer to the walnut? If so, looks nice!
  15. I did actually mention size in my previous...

    I did actually mention size in my previous "wall-o-text" reply, but it's easy to miss. Overall size: 66"L x 16"W x 35"H

    There is a rear rail under the top that runs the full length from leg to...
  16. Very true! I'll have to think about this a...

    Very true! I'll have to think about this a bit... it would be neat to make my own knobs.
  17. Thanks, everyone, for the feedback! I'll try to...

    Thanks, everyone, for the feedback! I'll try to answer all of the questions here, and I'm whipping up a couple more renderings to show the internal assembly and with the lower shelf up a little...
  18. Sideboard / sofa table - First table project, looking for feedback

    Hello, fellow woodworkers! I hope you're all having an excellent week, so far. First, let me make a note: the image I attached is just a render, not a physical object, yet.

    In talking with my...
  19. Thanks, Robert. I've seen a few mentions of...

    Thanks, Robert. I've seen a few mentions of Cutech, but don't know much about them. Discussions have been positive, though. So, I wouldn't rule them out. It seems spiral cutters pull more current...
  20. Good points, Bryan. Thanks for mentioning the...

    Good points, Bryan. Thanks for mentioning the service centers. Hadn't even crossed my mind.
  21. While that's all anecdotal, it's still good to...

    While that's all anecdotal, it's still good to hear your experiences. Thanks for sharing. From a whole bunch of reading, it seems that it can be hit-or-miss with Grizzly products. Maybe some are...
  22. Thanks, Bryan! Sounds like the Dewalt is a...

    Thanks, Bryan! Sounds like the Dewalt is a workhorse. Did you have any issues working with Grizzly as a company? Or just prefer the design, fit, and finish of the Dewalt over the Grizzly products...
  23. Replies
    8
    Views
    1,447

    That's a great idea! Someone beat Milwaukee to...

    That's a great idea! Someone beat Milwaukee to the punch. Thanks for sharing.
  24. Thanks for the input, Earl. That's really quite...

    Thanks for the input, Earl. That's really quite helpful. It sounds like DeWalt really put a lot of thought in getting the most from their design.

    Are you running on a 20A circuit or 15A circuit?...
  25. Opinions and experiences with Grizzly G0889 Planer?

    I'm looking around at getting a planer. I realize most recommendations point to the DeWalt DW735X, and for many good reasons. However, being a beginner and not spending a ton of my time doing...
Results 1 to 25 of 425
Page 1 of 17 1 2 3 4