Search:

Type: Posts; User: Steve Wurster; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Jeffrey, I've seen that same video, and that's...

    Jeffrey,

    I've seen that same video, and that's the inspiration for my question as well. I have a Hammer K3, and their equivalent extension table. I also have an Incra positioner in place of the...
  2. Sounds like a plan. Thanks!

    Sounds like a plan. Thanks!
  3. Erik, I realize this is an old thread and that...

    Erik, I realize this is an old thread and that you don't work for Minimax anymore, but I was wondering if you remembered or had pictures of how that Jointech unit was mounted to that extension table?...
  4. Revisiting this thread since I just used a...

    Revisiting this thread since I just used a positioner and my outrigger fence this weekend to rip a bunch of pieces. I've got an Incra positioner attached to a jig that registers against the little...
  5. Replies
    11
    Views
    667

    Jim, I'll PM you later about having you over for...

    Jim, I'll PM you later about having you over for a shop visit.
  6. Replies
    11
    Views
    667

    That's basically how I felt. Plus I doubt I...

    That's basically how I felt. Plus I doubt I could make them as nice on my own, or at lower cost factoring in my own labor time. Yeah, the 5" models aren't super cheap, but I'll eat the cost for the...
  7. Replies
    11
    Views
    667

    Magport DC Fittings...

    I have a small basement shop, so the only tool that has a permanent DC hookup is my table saw. Everything else (bandsaw, jointer/planer, router table) are on wheels, moved into position for use, and...
  8. Replies
    125
    Views
    6,866

    Sticky: Please register me. Thanks!

    Please register me. Thanks!
  9. Ed, I haven't gotten a PM. I hope they're not...

    Ed, I haven't gotten a PM. I hope they're not broken again!
  10. Various DC fittings, etc. - Philly suburbs - Free to good home

    I've got some 4" and 2.5" DC fittings, elbows, wyes, clamps, blast gates, etc., and a little bit of hose available to anyone (in my area) that wants it. My system is now all 5", so I don't need any...
  11. That is an incredible price for that saw! You up...

    That is an incredible price for that saw! You up for selling just the concentric clamp and the dado set? I already own a K3 Winner 78x48 with a bunch of blades, so I don't need any of the other...
  12. Replies
    22
    Views
    1,170

    Yes, the machine appears to behave normally...

    Yes, the machine appears to behave normally otherwise. So for now I'm just letting it go and will keep an eye on it.
  13. Replies
    22
    Views
    1,170

    Update: I put a new belt on yesterday and still...

    Update: I put a new belt on yesterday and still got the same noise when running. However I noticed that the belt was "flopping" a bit so I increased the tension (which is a pain to do on this...
  14. Replies
    22
    Views
    1,170

    There's a curious lack of "strange" noise coming...

    There's a curious lack of "strange" noise coming from the motor itself, when run either standalone or with the belt attached.

    The cutterhead makes minimal noises when spun freely (without the belt...
  15. Replies
    22
    Views
    1,170

    I do have a medical stethoscope on hand, but...

    I do have a medical stethoscope on hand, but didn't get it too up close to the motor; I just held it under the cabinet to see if I could hear anything specific. I can try that later today - I still...
  16. Replies
    22
    Views
    1,170

    Is there anything I can do to verify that? ...

    Is there anything I can do to verify that? Getting to the motor on these is not an ideal scenario, unfortunately.
  17. Replies
    22
    Views
    1,170

    I haven't noticed any interference with the...

    I haven't noticed any interference with the cutter head. If I remove the belt and free-spin the cutterhead via its pulley there is no banging of any kind. At this point I'm thinking this is...
  18. Replies
    22
    Views
    1,170

    Not that I can see or hear. There's nothing...

    Not that I can see or hear. There's nothing stuck in the dust collector shroud that I'm aware of, especially since the noise happens regardless of the position of that shroud.

    And I don't see...
  19. Replies
    22
    Views
    1,170

    Thanks. I think it's something at the cutterhead...

    Thanks. I think it's something at the cutterhead level. I got the belt off yesterday and the motor sounded just fine on its own (just a nice quiet hum). After putting the belt back on and running...
  20. Replies
    22
    Views
    1,170

    Once I get the belt off I can take a look. Plus...

    Once I get the belt off I can take a look. Plus removing the belt will let me know if the problem is in the motor or the cutterhead, since I'll be able to run the motor on its own.
  21. Replies
    22
    Views
    1,170

    I'll have to check that, however I'm not sure how...

    I'll have to check that, however I'm not sure how this belt comes off! The tension mechanism on this thing seems strange, and a quick glance at the manual didn't seem to be much help. I'll have to...
  22. Replies
    22
    Views
    1,170

    Yes, it's that "rat-a-tat-tat" sound that's very...

    Yes, it's that "rat-a-tat-tat" sound that's very prominent near the end as the cutter head is stopping. That's completely new; it never did that in nearly 3 years of ownership. And the planer...
  23. Replies
    34
    Views
    4,977

    Hammer A3 Noise...

    I posted this in the main forum as well. I have not yet called support; I was hoping to get an answer from here before going that route.

    My Hammer A3 31 just started making this clicking noise...
  24. Replies
    22
    Views
    1,170

    Hammer A3 noise...

    My Hammer A3 31 just started making this clicking noise when running; see video at link HERE. It happens in both jointer and planer mode, so it's not related to the planer rollers. The belt seems...
  25. I have the Dewalt as well, and just used it and...

    I have the Dewalt as well, and just used it and Phil Thien's mortising jig (https://sawmillcreek.org/showthread.php?164255-Thien-mortising-jig-for-DW611) to make a ton of mortises for loose tenons in...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4