Search:

Type: Posts; User: Scott Buehler; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    1,225

    What was the problem?

    What was the problem?
  2. Replies
    75
    Views
    9,756

    I have the Bosch glide and it is great. I would...

    I have the Bosch glide and it is great. I would have went with the DeWalt, because that is what I've used for years with great success, but I did not want it sticking out so far in my new shop,...
  3. I have the 735, and unlike other planners, it...

    I have the 735, and unlike other planners, it actually does a great job at expelling the chips. With that being said, I have it hooked up to my cyclone. It would still make quite a mess with out the...
  4. Replies
    11
    Views
    1,137

    2 or 3hp grizzly cyclone. Affordable and work...

    2 or 3hp grizzly cyclone. Affordable and work great
  5. I had a similar issue last year with my z Axis,...

    I had a similar issue last year with my z Axis, it ended up being a bad wire. I could not see any damage to the wire, but when I jumped it with a new wire, problem was solved. Not sure if that could...
  6. I have the 0441 and it works great! I would...

    I have the 0441 and it works great! I would definitely go that route unless ceiling height is an issue.
  7. Alot of the high school around me are getting...

    Alot of the high school around me are getting entry level CNC machines for the kids to learn, kids love technology! But I think joiners and table saws are a must to learn about, basic joinery skills;...
  8. Replies
    12
    Views
    809

    I leave mine in the cup for a day or two until I...

    I leave mine in the cup for a day or two until I have a couple coats on each side. But don't leave it in much longer than that
  9. I agree with Jim, Power Tec from Amazon are a...

    I agree with Jim, Power Tec from Amazon are a great hose and great price.
  10. I see no need to pay for an expensive air dryer,...

    I see no need to pay for an expensive air dryer, maybe in automotive spraying? I have always used a water filter and, drain my lines periodically. If the original question was, can you use or how do...
  11. Replies
    55
    Views
    9,825

    Spray booth works great, good luck!

    Spray booth works great, good luck!
  12. Replies
    55
    Views
    9,825

    Mark, I got all my ducting from Clifco, down in...

    Mark, I got all my ducting from Clifco, down in Slc. Very reasonable pricing. I got my garage door through a guy I work with. Its a 8 x 12 door, insulated with metal backing. It was about 1300.00...
  13. https://sawmillcreek.org/showthread.php?263167-24-...

    https://sawmillcreek.org/showthread.php?263167-24-x-26-shop-build
  14. I built a cheap spray booth in my build("24 x 26...

    I built a cheap spray booth in my build("24 x 26 shop")and it works great.
  15. I have had both, and they are both great fences....

    I have had both, and they are both great fences. I still have my old contractors saw that I use for dados and it has a beismeyer fence on it, 20 plus years old and still as accurate as the day I...
  16. Replies
    22
    Views
    1,895

    Nordfab and air handling mashes nice duct, but...

    Nordfab and air handling mashes nice duct, but very expensive. I buy from a local hvac and speak pipe manufacturer. It was a fraction of the cost and even though it's a bit more work, it works great!
  17. I agree with the above posts. Your compressor...

    I agree with the above posts. Your compressor should have a regulator on it already, you shouldn't need an Oiler and a water separator is all you should have to purchase. No need to buy a very...
  18. Replies
    55
    Views
    9,825

    Thanks Van, yeah not sure on how they work the...

    Thanks Van, yeah not sure on how they work the price on heaters, but that makes sense, lol. Yes the haze from the wildfires had been crazy this last month!
  19. I like using spaceballs between my panels and my...

    I like using spaceballs between my panels and my rails, it helps with the expansion and contraction of panels, and the joints between stile and rails are usually snug with no gaps..just my method for...
  20. Replies
    55
    Views
    9,825

    I finished running my duct this past weekend,...

    I finished running my duct this past weekend, except for about a4' section of 4" running to my miter saw, which I'm picking up tomorrow. I ran my main line 7" and reduced to6" to each drop, then to...
  21. Replies
    55
    Views
    9,825

    391105 391106 Finally picked up my ducting...

    391105
    391106
    Finally picked up my ducting order and will start running to each machine, It will be nice having the dc back up and running :)
  22. Replies
    55
    Views
    9,825

    Thanks Michael, it works great! Not as good as my...

    Thanks Michael, it works great! Not as good as my industrial fan of course but it's for my home shop. Its a Canarm explosion proof fan, it claims 3600 cfm and think that is fairly accurate.
  23. Replies
    6
    Views
    701

    And yes, Murphy Door and Murphy bed are not...

    And yes, Murphy Door and Murphy bed are not related at all
  24. Replies
    6
    Views
    701

    I actually work at Murphy Door, here in Ogden,...

    I actually work at Murphy Door, here in Ogden, Utah. All the info on the hinges are in the website. Are there questions you have that are not in there?
  25. Replies
    4
    Views
    806

    Not positive, but those all seen way overpriced...

    Not positive, but those all seen way overpriced fur being used. Just my 2cents
Results 1 to 25 of 137
Page 1 of 6 1 2 3 4