Search:

Type: Posts; User: Thomas Wilson; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    12
    Views
    1,175

    Not a lot of visible progress last week. (I am...

    Not a lot of visible progress last week. (I am doing Christmassy stuff in Atlanta for a few days right now.) I have mostly been thinking about how to connect up the duct work. I perhaps I should...
  2. Replies
    13
    Views
    471

    I am glad to see you were able to wrap your brain...

    I am glad to see you were able to wrap your brain around this project, Dr. Alvarado.
  3. Replies
    24
    Views
    1,113

    Good advice in James Harrison’s video. I made a...

    Good advice in James Harrison’s video. I made a bunch of fake beams 16’ long. These were 3 sided beams that fit over a 2x4 on a cathedral ceiling. The only way to do them was a 45 degree bit in a...
  4. Barbie could probably use that plane. ...

    Barbie could probably use that plane. https://www.instagram.com/barbiewoodshop/
  5. Replies
    119
    Views
    8,371

    Well, I will now.

    Well, I will now.
  6. One thing to be aware of with measuring the...

    One thing to be aware of with measuring the pressure drop across the filter is that the resistance in the rest of the flow network affects flow and thus the measurement. You want to take a reading...
  7. Replies
    13
    Views
    768

    If you did actual birdsmouth joints using narrow...

    If you did actual birdsmouth joints using narrow stock to make rings with a bit of overhang on each joint and made a stack of them in decreasing size alternating the orientation of each ring, the...
  8. Replies
    119
    Views
    8,371

    If I didn’t have a tail vise, where would I clamp...

    If I didn’t have a tail vise, where would I clamp my pencil sharpener.
  9. Buy or make a rolling base for the drum.

    Buy or make a rolling base for the drum.
  10. Replies
    119
    Views
    8,371

    Congratulations to Miss Rawlings for effective...

    Congratulations to Miss Rawlings for effective teaching and to your neurons for the long lasting memory. I may have been offered the same knowledge in Mrs. McMullins’ English class in 10th grade but...
  11. Stephen, this a helpful article about thin kerf...

    Stephen, this a helpful article about thin kerf blades and the riving knife. Trent Davis is a technical guru and service representative with SawStop....
  12. Replies
    2
    Views
    211

    You can delete the photo from the main text but...

    You can delete the photo from the main text but it just goes to a “lame user” bar at the bottom of the post.

    About the rotation, on my Apple devices, images appear in the orientation that I took...
  13. Replies
    119
    Views
    8,371

    Kevin, I had to look up two words in a 33 word...

    Kevin,

    I had to look up two words in a 33 word post. Excellent!

    TW
  14. Could be dull blade. Do you have a newer sharper...

    Could be dull blade. Do you have a newer sharper blade to try?

    Do you have the riving knife installed? Even if you do, releasing internal stress in the wood can close up the kerf enough to...
  15. Replies
    12
    Views
    1,175

    Ron, you are all set now. But for others setting...

    Ron, you are all set now. But for others setting up a new system, Nordfab does make custom components for a reasonable price if you go through a retailer who can make the measured drawings needed. ...
  16. Replies
    12
    Views
    1,175

    Thanks Kevin. Good point. The collector is in a...

    Thanks Kevin. Good point. The collector is in a closet in the basement.

    In this case the alignment is dictated by the piping constraints to get the pipe up and out of the closet. Believe me,...
  17. Replies
    12
    Views
    1,175

    Thanks, Ron. From my vast experience of cutting...

    Thanks, Ron. From my vast experience of cutting exactly one pipe cut so far, the allure of a new tool is not quite enough yet. The jigsaw with a fine tooth metal cutting blade method worked really...
  18. Replies
    12
    Views
    1,175

    17” main is huge. I am using 6” main with 6x4x4...

    17” main is huge. I am using 6” main with 6x4x4 branches above the floor to connect to machines. I work alone so only one machine will be connected at a time. I need to keep velocity up in the...
  19. I am installing a stationary dust collector but...

    I am installing a stationary dust collector but my older system may be similar to yours. It is a 2 HP Oneida portable. I too struggled with a simple way to connect to both the SawStop Floating...
  20. Replies
    12
    Views
    1,175

    My duct work and dust collector came in a few...

    My duct work and dust collector came in a few weeks ago. I have been traveling so not much progress has been made. Today, I hung the collector on the wall bracket temporarily using some drywall...
  21. Replies
    13
    Views
    1,673

    The Stanley Sweetheart set of chisels set has all...

    The Stanley Sweetheart set of chisels set has all the intermediate sizes. I have other sets but not as complete. The edge holds up well enough for my usage that tends more toward paring than...
  22. Plywood might have some warp so that fully...

    Plywood might have some warp so that fully threaded screws hold the plywood away from studs. A clearance pilot hole in the plywood allows the plywood to be pulled down snug. A better solution is...
  23. Thread: saw stop

    by Thomas Wilson
    Replies
    40
    Views
    2,307

    Have you tried calling SawStop about the hole...

    Have you tried calling SawStop about the hole alignment problem? They are very good with customer service. Also, there is an adapter kit to convert the industrial mobile base for use with the...
  24. Replies
    1
    Views
    296

    I have cut it with a cope and stick router bit...

    I have cut it with a cope and stick router bit set. You start with a wide workpiece, then rout one edge with cope bit. This will be used as the holder for the second cut on the two-sided molding. ...
  25. I have the original Performax 16-32 also. A...

    I have the original Performax 16-32 also. A strong vacuum like Ridgid 6.5 HP works surprisingly well on the 2 1/2 port. To collect airborn dust that escapes, I use a big dust hood on a stand...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4