Search:

Type: Posts; User: Rich Aldrich; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.25 seconds.

  1. Replies
    19
    Views
    1,230

    For the Dewalt DW 735, if you have a good dust...

    For the Dewalt DW 735, if you have a good dust collection system, you can take the fan off the motor to reduce noise. Dewalt recommends removing the fan when connected to a dust collector.
  2. Thread: Dw735

    by Rich Aldrich
    Replies
    19
    Views
    1,125

    If you have a good dust collector Like a cyclone,...

    If you have a good dust collector Like a cyclone, remove the blower. It will make it quieter. It also give you more power if you decide to install a shelix head.

    I had a DW735 until a few months...
  3. Replies
    17
    Views
    710

    I havent convinced myself to buy a drum sander...

    I havent convinced myself to buy a drum sander yet. To flatten the rings, I am going to try Cole jaws and turn the face flat followed by face sanding on a flat plate.
  4. Replies
    17
    Views
    710

    I checked out some of the prices on ebay - not...

    I checked out some of the prices on ebay - not too bad. I saw a few of these lathe set ups on You Tube Univeristy.
  5. Replies
    17
    Views
    710

    This looks l like a nice set up. I saw a couple...

    This looks l like a nice set up. I saw a couple of plans similar to this. It does tie up the lathe, but it looks like it is fast to set up and take down.
  6. Replies
    17
    Views
    710

    I have a Rigid belt / spindle sander, but the...

    I have a Rigid belt / spindle sander, but the belt pushes parallel to the table, so you don't have control like you would with the disc sander. I know I would use it for a lot more than segmented.
  7. Replies
    17
    Views
    710

    I was wondering about the wedgie sled. I watched...

    I was wondering about the wedgie sled. I watched a few You Tube University videos where they used the wedgie sled and just sanded by hand to clean up the wedges.
  8. Replies
    17
    Views
    710

    Disc Sander for Segmented Turnings

    I am planning to try some segmented turning. So this is a good excuse to add a new tool. My understanding is that disc sanders are hand for finishing sanding segments.

    I am looking for...
  9. Replies
    11
    Views
    890

    I had vibration issues with chatter pattern on...

    I had vibration issues with chatter pattern on the wood from my Jet 6" jointer purchased in 2001. I went through set up with the straight knives and really didn't change the vibration issue. Maybe...
  10. Replies
    19
    Views
    1,081

    I have a Powermatic 209HH. The only issue I have...

    I have a Powermatic 209HH. The only issue I have had with denting wood through the planer is when I plane pine. The pitch tends to make particles stick to the feed and bed rollers. My dust...
  11. Replies
    3
    Views
    319

    I bought a used Powermatic 209HH used for $2500...

    I bought a used Powermatic 209HH used for $2500 about 2 months ago. I like it so far. I do have to replace a few things due to wear but I expected that since it is used. I thought it would take a...
  12. Replies
    29
    Views
    1,220

    Clearvue has a forum that where one person shows...

    Clearvue has a forum that where one person shows the way they put their Clearvue on wheels. There is a section on that forum that people post pictures of their Dust collector arrangements.

    I have...
  13. I buy batteries off ebay. You can get the name...

    I buy batteries off ebay. You can get the name brand for a lot less than many places. . I would try one new battery and decide from there. If you know of anyone nearby with newer cordless,...
  14. Replies
    34
    Views
    1,936

    +1 on the Kreg jig.

    +1 on the Kreg jig.
  15. Replies
    14
    Views
    868

    I made mine adjustable like Chris posted - he...

    I made mine adjustable like Chris posted - he suggested it to me and I watched the video he attached. The issue I have with my shop floor is it was an addition, so the floor isn't perfect where the...
  16. Replies
    15
    Views
    1,063

    Thanks for the input. I saw the post in another...

    Thanks for the input. I saw the post in another forum that Eurekazone will be starting up after relocating. My anti chip strips should last until they start up again or until we see they don't start...
  17. Replies
    15
    Views
    1,063

    Kreg reviews haven't been stellar. Due ti getting...

    Kreg reviews haven't been stellar. Due ti getting stuck with this system, I agree it is worth getting a Makita or Festool.
  18. Replies
    15
    Views
    1,063

    There is a anti chip tab you can click on, but it...

    There is a anti chip tab you can click on, but it comes up blank. It appears they have none left.
  19. Replies
    15
    Views
    1,063

    TrueTrac Saw

    Does anyone have the TrueTrac Saw system? https://www.truetracsaw.com/

    I have the EurekaZone system that I will have to replace when I run out of anti-chip guides.

    I have been considering...
  20. Replies
    12
    Views
    901

    I just installed a 220 V circuit for a new to me...

    I just installed a 220 V circuit for a new to me planer. It is a Powermatic 209HH and has a 5 HP motor with 28 FLA. I did go ahead and install #8 wire and a 40 Amp breaker. My Clearvue Cyclone has...
  21. We had to do this a couple of times for short...

    We had to do this a couple of times for short term repairs at the papermill where I used to work. This application isnt as tough, and if I combine this method with the Loctite product, it might be...
  22. Loctite does make a decent product according to...

    Loctite does make a decent product according to my local Motion rep. Neither of us are fans this method but maybe I should try it.
  23. I thought the answers I have posted were clear,...

    I thought the answers I have posted were clear, but apparently not. I don't think it was how the saw was operated, but I would be bias in that regard. I am not sure how you could do the damage...
  24. The issue I see with the unisaw arbor is the...

    The issue I see with the unisaw arbor is the lowest price is $174 that I found so far. I am not even sure if they are new.

    There is a machine shop in Green Bay, WI - 3 hours from here - that does...
  25. I agree. That is why I am looking into the...

    I agree. That is why I am looking into the proper shaft size. I will have them make the shaft the bigger proper size where the bearing is supposed to be on the shaft. The other observation about...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4