Search:

Type: Posts; User: John Gornall; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.24 seconds.

  1. Replies
    22
    Views
    1,615

    ctdsaw.com

    ctdsaw.com
  2. Replies
    13
    Views
    874

    Lee Valley sells a "double t-slot track" that...

    Lee Valley sells a "double t-slot track" that slides into a tablesaw miter slot and converts it into a t track

    They don't show it in a tablesaw slot but it fits my Unisaw perfectly and I use it...
  3. I have had a V-3000 for about 10 years. It's used...

    I have had a V-3000 for about 10 years. It's used in a production situation on a single machine cutting prefinished moldings which produces very fine dust. Runs about 4 hours each day, 5 days per...
  4. Replies
    66
    Views
    8,302

    At my supplier last week. Full color label on the...

    At my supplier last week. Full color label on the 1/2" :

    "Russian Birch - Made in Viet Nam"
  5. Replies
    7
    Views
    1,287

    Not something I had a problem with - a little...

    Not something I had a problem with - a little movement but cuts fine
  6. Replies
    7
    Views
    1,287

    Neanderthal cut off saw update

    Another woodworker thought I was joking. I have found this a great solution for a cut off saw in my shop.

    I see permanent chop saw stations with 16 feet of counter space - no thanks.

    I can put...
  7. Yes, when the cut is finished. The guides ride on...

    Yes, when the cut is finished. The guides ride on the spine when sawing wood.
  8. On a Langdon type miter box the saw doesn't ride...

    On a Langdon type miter box the saw doesn't ride on the guides

    The guides ride on the saw

    Until the last stroke
  9. https://www.leightools.com/bridge-piece-material/

    https://www.leightools.com/bridge-piece-material/
  10. It's the actual cut being straight that counts....

    It's the actual cut being straight that counts. Lay the rail on a sheet of plywood. Clamp it so it won't move. Using the Makita scoring feature cut a shallow kerf the length of the plywood. Pull a...
  11. For small work including face frames I use the...

    For small work including face frames I use the Veritas mini bisquits from Lee Valley. The slot is cut with a slotting bit in your router table - precise.
  12. The Makita track saw has a scoring function that...

    The Makita track saw has a scoring function that justifys owning it for me. Just push a little button and depth of cut is 1 mil. Run the scoring cut, pop the button out and make the full cut. Cutting...
  13. I have a CTD double miter cutoff saw (2 blades, 2...

    I have a CTD double miter cutoff saw (2 blades, 2 motors) still perfect after 30 years - however only 45 degree cuts
  14. I designed and drew plans for my new house....

    I designed and drew plans for my new house. Involved my contractor in planning. Was planning a separate shop about 24' X 32'. Looking at the plot plan I wondered about making the shop part of the...
  15. Replies
    10
    Views
    1,086

    North Brothers (Yankee) 1550 is a breast drill...

    North Brothers (Yankee) 1550 is a breast drill with the same left/right hand mechanism
  16. Replies
    10
    Views
    1,086

    North Brothers 1530 hand drill works right or...

    North Brothers 1530 hand drill works right or left handed at the click of a switch

    https://www.timetestedtools.net/2016/07/30/north-brothers-yankee-no-1530a/
  17. I bought Pony pipe clamps about 40 years ago,...

    I bought Pony pipe clamps about 40 years ago, they work well. I bought parallel clamps a few years ago, don't use them much, prefer pipe clamps. I use a lot of 1/2" pipe clamps, small clamps for...
  18. Edge jointing a board There was a mention...

    Edge jointing a board

    There was a mention about pushing a board thru a jointer with your thumb. This is how I was taught by the old German cabinetmaker that I worked under those many years ago....
  19. Seldom any operating instructions with machines....

    Seldom any operating instructions with machines. I try to understand why the machine design is the way it is. The Euroguard on my hammer is adjusted down close to the workpiece and is spring loaded...
  20. Replies
    11
    Views
    1,071

    Glenn, could you post a few more pictures of you...

    Glenn, could you post a few more pictures of you setup, thanks
  21. Replies
    34
    Views
    3,464

    My shop is on an island in a rain forest near the...

    My shop is on an island in a rain forest near the ocean - no rust

    The key is understanding humidity (hydrodynamics) - used to be part of my job as an engineer

    Right now it's 44 degrees and 80%...
  22. Replies
    16
    Views
    4,510

    An excellent video and very helpful - Thank you

    An excellent video and very helpful - Thank you
  23. The lever quick release was sold seperately to be...

    The lever quick release was sold seperately to be added to the clamp. I had some, found them to be a knuckle buster, gave them away.
  24. Replies
    10
    Views
    920

    It's been many years but if memory serves I used...

    It's been many years but if memory serves I used a drive pin and a ball pean hammer to push the pin - only needed a few thou to tighten the fit
  25. Replies
    10
    Views
    920

    I did a little adjustment to the pin to keep the...

    I did a little adjustment to the pin to keep the small part of the chip breaker tight against the shoulder of the big part

    My Clifton 3 is my most used plane - have 5 and 7 Clifton's as well
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4