Thanks Stan. I found a gallon worth of it on a certain e-commerce site. I were just wondering if people use other type of oil besides the one listed in the manual and on W&H's website.
Type: Posts; User: Wakahisa Shinta; Keyword(s):
Thanks Stan. I found a gallon worth of it on a certain e-commerce site. I were just wondering if people use other type of oil besides the one listed in the manual and on W&H's website.
Pictures may help. Maybe the below may give you ideas on how to adjust yours.
455299 455301
On Felder/Hammer saws, the fence's adjustments are made by manipulating the fence's round-steel rail...
Before you buy a Felder machine, become a member of the Felder Owners Group (https://groups.io/g/felderownersgroup). A lot of people can advice you about machine and options there. Occasionally,...
Hello. I recently acquired a Williams Hussey molder, model No. 154 given the serial number in relation to the manuals provided on WH's website. The electronic manual specifies gear oil from WH or...
I see now that I looked at picture #4 more closely. Nice machine work! I couldn't tell the suggestion of the mating surfaces at first in that picture until after you answered and I returned for...
Brian, did you machine the L-stop out of one solid block of brass? I like the pneumatic clamp! I will remember this detail for future reference.
There are a few ways I rip using my KF700SP.
With two parallel fences (or one flip stop + one parallel fence) attached to the sliding table, the stock is referenced to the parallel fences then...
What are you going to build? Are you going to work with sheet goods, or solid wood, or both? For sheet goods, small shop, and a finite budget, then a good track saw and a small slider are excellent...
Thanks everyone. I measured the "good" oil cup on my General 220. Though the measurements with a digital caliper is not an exact match with Gits's specs, they are close. Maybe the Gits 00801...
Hello,
I am restoring a General 220 hollow chisel mortiser that once belonged to a high school's woodshop class. It was abused, but still in good shape. There are two oil cups that hold oil for...
I rip using either the sliding table and the rip fence, depending on the work flow. You can make you own parallel rip guide for the sliding table with DIY wooden T-nut, scrap woods, etc. before you...
John, what do you use to clean your gun after spraying Lenmar Duralaq? I read the TDS, but want to hear your real-time method.
I have been spraying BM Advance with a Fuji Q5 and T75G gun, but...
Thank you for your advice and offer of support. Below is more history.
To answer some of the questions raised previously, the machine impacted twice on its way down to the ground; once when the...
To make a very long story short, I now have a used woodworking machine, about 2100+ pounds in weight, laying upside down in the middle of my driveway with scattered parts here and there, after being...
A main reason I bought the A3-31 with the "Silent" cutter head was because Felder had a showroom near where I lived. After 6 years, I am on the 2nd edge of the cutters and have a set on the shelf...
I am curious about a few things. Is that tear out in the second picture, mortise #2 from left nearest to the camera position? Is this common for a chain mortiser? Looking at the chain, it seems...
The peripherals for the K3 do not have to be expensive. I modified this clamp to work with the K3. I have two, front and back. I also use these clamps with a wooden T-nut in the slider table's...
A very quick decision.
A primer on sliding table calibration. Link. When I received my K3, it was reasonably calibrated. If you want tighter tolerances, then you will need some basic...
Sign up --> https://groups.io/g/felderownersgroup
That secondary saw/blade excels at cutting tenons. Its capabilities are demonstrated in a lot of Ishitani Furniture videos, which are quite relaxing to watch.
Brian, these were purchased from Japan tool, whose store owner is So Yamashita.
We really veered off course! Getting back to the topic of the thread.
Are the various manufacturers of Japanese short-stroke slider equivalent in quality of their machines?
The little...
This is not too difficult to make from scrap plywood. I have more than a few, in different lengths, spacing, etc. The longest one is made from a 6-foot 1/2-inch thick plywood scrap, about 10 inch...
Mark, my understanding is that Marunaka makes a grinder for the disposable knives. I suppose you can not grind the disposable knives too many times, but how many times can you grind them? Does it...
Christopher, the handles are made from rosewood.