Hello,
I had a bit of a scare the other day where one of my Freud router bits sheared off at the shank (1/2") while making dados (I was making a 13/32" deep cut with the 3/8" solid carbide spiral...
Type: Posts; User: Matt Przybylski; Keyword(s):
Hello,
I had a bit of a scare the other day where one of my Freud router bits sheared off at the shank (1/2") while making dados (I was making a 13/32" deep cut with the 3/8" solid carbide spiral...
Steve,
Yes I did and its a workhorse, I like it a lot. The digital readout is useless because its battery powered and after the batteries died I didn't bother putting new ones in because I just...
"Standoffs" was the key word I was missing, thank you very much!
I'm looking at finding out what the offsets are that hold this piece of glass off the wood behind it? I don't know what to call them but would like to purchase some for a project I have in mind and...
lol, none taken, and you're probably right, but i was able to take a heat gun to it to loosen it up and came right off. its reusable for the next time and I'm all set :)
Completely understandable, but this one was never used and brand new so I didn't want to waste it. I know they are only like $20 for a 5 pack, but i don't like wasting brand new things :) that's...
Closing the loop here, spoke to Fuji today and they suggested cutting it to get it off. I'm trying to preserve it as its a brand new tube so before doing so I'm going to try and use a heat gun on it...
I should have added that I don't want to damage the tube as its a brand new gun and i'm hoping to salvage it for later reuse. I'm going to try using a heat gun on it today but I'll also be calling...
Trust me, I tried pulling very hard. What do you mean by "flip the valve it works with the remote pot"? This is the pressure tube on my gun.
I'm trying to prepare my Fuji T70 gun for connection to my pressure pot and I can't for the life of me remove the pressure tube that connects to the gun. Its on there extremely tight and as it sits...
Apologies for resurrecting an old thread, but I'm considering buying this PP and I also have the gravity fed gun (both of the ones Fuji makes, actually). Is it a pain in the butt to use the pressure...
Yep, I actually have the same as you, a flat tip on my dial indicator, but was just trying to follow the directions to a T so that I am doing what the manufacturer suggested exactly. Obviously it did...
Matt, the instructions for adjusting the roller parallelism to the bed state to rotate the rollers to find center and they state that when in neutral the rollers should move. That is not the case so...
In doing more and more research it seems like this is the norm. I do have a digital height gauge but have yet to install it on the planer so I think that'll be my next step and I'll follow the...
Hello,
I have the aforementioned planer from Grizzly and I'm having 2 issues.
1) No matter what I do, I cannot move the infeed or outfeed rollers manually, its like they're stuck. Even if I put...
Tony, I was informed multiple times about dates and each time it got extended again and again. I would not count on getting yours on 11/15, to be honest.
Thank you Shiraz, I kind of figured this. I'm in AZ so I should get it probably within a week or so from WA. I do like the rack and pinion fence and other things on the 0495X. I have read about the...
Shiraz, thank you for chiming in. I'd appreciate your honest opinion please. Should I cancel my order for the 0495X and order this new jointer instead? I'm ok with waiting until early December to get...
I cancelled the 0490 order a long time ago because I got tired of waiting on it. they told me one thing and then continually delayed it so it didnt really matter. I finally just bit the bullet and...
I'm in the market for an 8" jointer and just saw this pop up (available in November) on the Grizzly site. I'm wanting an 8" parallelogram with spiral cutterhead.
...
Jim, the Grizzly variant is not large enough for the base of the planer.
Of course I answered my own question just after posting this. Looks like this will do the ticket: https://www.rockler.com/htc3000-universal-mobile-base
Still would love to hear what others have...
Hello,
I'm thinking about purchasing this: http://www.grizzly.com/products/Grizzly-8-x-84-Jointer-with-Exclusive-Digital-Height-Readout/G0495X
It does not come with a mobile base and looking at...
That's actually what I was going to originally do and the way I'm leaning, just wanted to see if I could find veneer this long to not have a seam. :)
Thanks Jamie, I emailed them to see if they have 15' rolls as a special order. I was planning on using contact cement to apply the veneer to MDF substrate.
That being said, I was unable to find...