Three other 3-phase machines are running fine, so it is not the Phase Perfect.
I did, however, replace the capacitors a few years back.
Thanks
Type: Posts; User: Dennis Yamamoto; Keyword(s):
Three other 3-phase machines are running fine, so it is not the Phase Perfect.
I did, however, replace the capacitors a few years back.
Thanks
I understand that the breaker should be able to pass its full rated current unless tripped by an overload. I was wondering if a failing breaker could be ON but not pass its rated current. Probably...
I have purchased several Lenox resaw blades including a Woodmaster CT 1.3 TPI from Industrial Blade in Santa Ana. The Woodmaster is either 27 or 54mm wide.
I removed the jumpers for delta configuration and checked the resistance at the six terminals:
0.4 ohms between U1 and U2, V1 and V2, W1 and W2.
infinite between each of the above windings or...
When I first got the bandsaw, the belts were old and slipping so I replaced them. I don't think they are slipping now. I suppose I could stop the blade or the lower wheel and see if the pulley is...
I have a Minimax Centauro S600P/MM24 that I bought used. I can easily stop the motor resawing 6-10" hardwood. I presume the previous owner overheated the motor windings.
The original motor is...
Hi Joe,
The Krenov School uses a Lenox Woodmaster CT 1.3 TPI 1" blade for resawing on their Agazzani bandsaw. Bigger gullets in the 1.3 TPI blade allow for more sawdust for a tall resaw. I have...
Hi Josh,
A number of folks on the Felder Owners Group use Tenryu blades.
I use the following combination blade on my CF741 most of the time. If I'm ripping 8/4+ material that is really hard, I...
Another thought: it's approximately 5/16". Given your drawer box opening and drawer side thickness, use Blum's instructions to calculate the drawer box width which will give you the side recess. If...
I believe that Blum tandem 563H's require about a 5/16" side recess. So, if you want to do half blind dovetails in front for an inset drawer, you will have to account for this. I did this by using...
I use what the Krenov School used a few years ago: Intertape 591. It does take some effort to remove, but you don't want it to come off when you are template routing or shaping. It's the only thing...
The Blum boring jig does work with Movento's. I just used the jig on both Movento 763H and 769 slides.
Both left and right sides provide a rear tilt adjustment to tilt the front of the drawer forward. It looks like the one on the left is raised higher. Rotate the grey tabs to adjust the tilt.
The...
I got this suggestion from Jamie in the Bay Area Woodworking Assoc: you can gang cut all of the half-laps by stretch wrapping all of the grid boards together that are the same length. In addition,...
I like Industrial Blade and Products, Santa Ana, CA for Lenox. Excellent prices, service and a nice weld.
Dennis
Did it work before?
Besides turning on the main power switch, the emergency stop buttons have to be disengaged. That is, turn them so they pop out. Also there are several safety switches. For...
Double bevel marquetry
A couple of people suggested using a Krenov coopering plane. Here's a picture of my Krenov coopering plane where I'm planing the concave side of a coopered door. It's some effort to shape the sole...
See Charlie's page:
http://www.solowoodworker.com/mm/switch.html
I have a 2005 MM16 and I'm on my 3rd switch
See John White's book, " Care and Repair of Shop Machines". In Chapter 2 on Jointers, he shows how to make a master bar for checking jointer tables. It's as economical as MDF and drywall screws.
I believe a 16" HD Northfield jointer weighs about 2000 pounds. I would guess that any mobile base would settle to however flat your concrete floor is. You could loosen the bolt and nut on the...
I got the DeWalt. It worked great for the knife hinges! I can see why so many folks recommend these small routers and especially the Dewalt.
Thanks everyone!
Dennis
Thanks everyone! Looks like the Dewalt unless I want something smaller like the Ridgid.
Mike,
Thanks for your suggestion for routing close to the line, and finishing with a chisel. I have a...
I need to route mortises for some small brass knife hinges. For routing these small mortises, what trim router would you buy today, and why? For me it seems like good depth adjustment, and having...
I don't like Felder's eccentric clamps. I find them difficult to set up just right. What some people do is to use a wood spacer. They put the spacer under the clamp head to set the clamp height,...