Search:

Type: Posts; User: Steve Rozmiarek; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.80 seconds.

  1. That's not popcorn, it's knockdown. Also not...

    That's not popcorn, it's knockdown. Also not helpful I guess :)

    Defiantly just use 3/4" boards and wrap it. Skip the veneer. Keep it simple. your life will be a lot easier and the customer...
  2. Replies
    5
    Views
    471

    I had a pep talk with a sawzall that I didn't...

    I had a pep talk with a sawzall that I didn't realize had 99.9% dead battery until i climbed into the far corner of the attic just yesterday. Something a little less refined than, "come on, it's...
  3. Replies
    46
    Views
    9,072

    Looks great, well done! The exposed cross ties...

    Looks great, well done! The exposed cross ties and cathedral ceiling above sure add to the space. Ages ago I had a shop with a ceiling like that and really liked it.
  4. I don't think there is any practical speed...

    I don't think there is any practical speed difference on rapid bump firing. Maybe if you were to just blast away on a board to race or something, but on a normal 3 nail plate to stud situation that...
  5. His gun needs Milwaukee service, they will fix...

    His gun needs Milwaukee service, they will fix that.
  6. Hi Jim, this is a good opportunity to campaign...

    Hi Jim, this is a good opportunity to campaign for like buttons :)
  7. Yikes Warren!! I've personally never taken that...

    Yikes Warren!! I've personally never taken that ride, but I suspect when I do, an airhose will be involved too. I'm hoping to see a Milwaukee roofing gun someday, no luck yet...
  8. The Milwaukee and Dewalt are different generation...

    The Milwaukee and Dewalt are different generation tech. I like Dewalt tools generally, but I gave away the dewalt nailers we tried. They are fine for someone I suppose, but too slow, huge ramp up,...
  9. The brad nailer has the same depth control, just...

    The brad nailer has the same depth control, just a little smaller. Works well! 18g brads still behave silly sometimes, don't get rid of the side cutters, but you will be pleasantly surprised at the...
  10. Yes, the newer generation Milwaukee are as good...

    Yes, the newer generation Milwaukee are as good as or better than air. They are the ONLY battery or gas powered nailer I will say that about. Milwaukee's guns are the only ones out there right now...
  11. Replies
    20
    Views
    1,541

    Had a very similar experience, unvented heaters...

    Had a very similar experience, unvented heaters are just plain dangerous. Kerosene is worse than propane IMHO, but they are both dangerous.
  12. That's a neat factoid! Adds some credence to my...

    That's a neat factoid! Adds some credence to my perspective too. I work with a crew of guys, and it's kind of like the old telephone game at times. Framer yells "16 3/16" to the saw helper, who...
  13. Replies
    5
    Views
    487

    Sure looks like all the old birch cabinets and...

    Sure looks like all the old birch cabinets and millwork that we replace.
  14. Replies
    12
    Views
    1,235

    We do it regularly with construction lumber, osb,...

    We do it regularly with construction lumber, osb, ply ect. Most of that stuff can actually store outside in this dryer climate for a long time before we have problems. That being said, like Maurice...
  15. Wish that was about 1000 miles closer.

    Wish that was about 1000 miles closer.
  16. But Jacob, the market value and hence demand is...

    But Jacob, the market value and hence demand is set by completed transactions, a completed transaction must occur to get a meaningful data point. What you describe is not actually letting the...
  17. Replies
    9
    Views
    567

    Nothing more to add about the power feeder, but...

    Nothing more to add about the power feeder, but that sounds like a neat project. How are you notching them? Lincoln logs, grandmas house, christmas, etc, good times!
  18. Replies
    53
    Views
    7,141

    Thank you Joe, that makes sense now that you...

    Thank you Joe, that makes sense now that you point it out. Rangate just sent me details on an option with this cutter to swap a component to cut conventional shaker too. Think I'll give it a try.
  19. Ditto. For me, a used machine that will cost...

    Ditto. For me, a used machine that will cost half of new replacement cost may be interesting, anything over that is not worth the effort. Cost INCLUDES the hassle of getting it into my shop,...
  20. IMHO, the prices for old iron have inflated so...

    IMHO, the prices for old iron have inflated so much that maybe they are finally hitting the point of pricing themselves out of the market. I love quality old iron, but when I can't find a used...
  21. Replies
    15
    Views
    927

    Here is the Felder guard I mentioned earlier. ...

    Here is the Felder guard I mentioned earlier. It's good enough that I always run the saw with it on. I just have the vacuum hose plumbed into the DC. Catches all the fines, a few bigger chips...
  22. Pretty easy to find it free with a saw, if you...

    Pretty easy to find it free with a saw, if you are buying a saw too.
  23. Does someone really think it's that complicated...

    Does someone really think it's that complicated to tension a bandsaw?
  24. Replies
    15
    Views
    927

    If you want something with a smaller footprint,...

    If you want something with a smaller footprint, the one that came with my Felder is pretty darn good. Mounts to the riving knife, so it'd probably fit others too. I don't have first hand experience...
  25. Replies
    53
    Views
    7,141

    Joe or others, probably a dumb question, what is...

    Joe or others, probably a dumb question, what is the reason that the set is designed to have a stepped door panel groove? Meaning, I'm used to seeing cutters were the the panel groove is just 3/8"...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4