Search:

Type: Posts; User: Steve Jenkins; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds; generated 35 minute(s) ago.

  1. Replies
    15
    Views
    759

    If you are saying the breadboards are longer than...

    If you are saying the breadboards are longer than the width of the top that is normal and why I don’t like them. The top will expand and contract across its width which is why you only glue the...
  2. Replies
    17
    Views
    1,127

    VERY nicely done

    VERY nicely done
  3. Replies
    3
    Views
    525

    NC is normally closed. Doh think of the simpsons

    NC is normally closed. Doh think of the simpsons
  4. Sticky: Useful looking set. I’m in

    Useful looking set. I’m in
  5. Replies
    2
    Views
    354

    It’s not in Iowa but an excellent source is...

    It’s not in Iowa but an excellent source is Talerico hardwoods in PA.
  6. I’ll second Dowd’s.

    I’ll second Dowd’s.
  7. Sticky: Looks like a great book. Count me in

    Looks like a great book. Count me in
  8. Replies
    20
    Views
    1,245

    I have one that I put on my router table for...

    I have one that I put on my router table for running small moldings. It works great
  9. I would finish separately and finish all.

    I would finish separately and finish all.
  10. I have a 1949 Oliver166. The cutter head and...

    I have a 1949 Oliver166. The cutter head and motor shaft are one solid piece. Don’t know how you could replace just the cutter head. I use Dispozablade knives in mine. They are straight knives but...
  11. THIS. Most times waxing the table solves the...

    THIS. Most times waxing the table solves the problem. As in most things try the simplest first.
  12. Replies
    13
    Views
    1,977

    Check Harlywax. It’s an easy to apply carnuba

    Check Harlywax. It’s an easy to apply carnuba
  13. Glue is enough. If you have some twist the...

    Glue is enough. If you have some twist the biscuits will help alignment. Did you try to joint the full 12’ length or cut to about 1”’ oversize then joint.
  14. What about using a threaded insert instead of a t...

    What about using a threaded insert instead of a t nut
  15. Replies
    8
    Views
    1,053

    When I’ve done that I’ve made a box that would...

    When I’ve done that I’ve made a box that would fit into the cabinet and mount the drawers in it. Slide in place and run a couple screws through the bottom into the cabinet bottom.
  16. Replies
    4
    Views
    448

    Started working again

    Started working again
  17. Replies
    4
    Views
    448

    Tried that. It shows unlocked but I cycled it...

    Tried that. It shows unlocked but I cycled it anyway. No change. It only happens on sawmill creek which is odd.
  18. Replies
    4
    Views
    448

    Screen doesn’t rotate

    I use my iphone12 and suddenly my screen doesn’t rotate when I turn the phone. It only seems to happen on SMC. Has always worked until today. Any idea?
  19. Replies
    9
    Views
    787

    Sounds like you are using top hat bushings. You...

    Sounds like you are using top hat bushings. You can get bushings that don’t have the ridge so you can stack cutters
  20. Replies
    607
    Views
    82,057

    Sounds like things are going in a good direction....

    Sounds like things are going in a good direction. Sorry about the sciatica.
  21. I’ve got an Extrema that I picked up for $500....

    I’ve got an Extrema that I picked up for $500. Just needed a new bit and had to make a couple fences. It works great. All my drawers are 9/16 thick and I index from the bottom edge so the fences...
  22. Replies
    18
    Views
    1,573

    If you look at the bottom frame by the dust...

    If you look at the bottom frame by the dust collection and blow it up it does look like SCMI on the ID plate.
  23. Replies
    607
    Views
    82,057

    Looking good Jim. If you haven’t doe it consider...

    Looking good Jim. If you haven’t doe it consider sloping the apron a bit for runoff.
  24. Replies
    15
    Views
    1,544

    I had to take apart 3 outside fans not for...

    I had to take apart 3 outside fans not for bearing but to remove mud dauber nests.
  25. Envious Jim. Really nice machine.

    Envious Jim. Really nice machine.
Results 1 to 25 of 497
Page 1 of 20 1 2 3 4