I just bought one on ebay for $35. Delta and other places wanted $70+.
Type: Posts; User: Mike Mulville; Keyword(s):
I just bought one on ebay for $35. Delta and other places wanted $70+.
Sorry guys I missed this suggestion. That pulley is 7/8" bore and I need 3/4".
Yup that's what the motor repair place said.
The bore is .75" and the outer diameter is 3.5" 3 groove.
I believe it's the 41-644 HD 3 groove pulley.
Finally got in there again and did some measuring. The motor pulley bore .750 on one end and .764 on the other. The motor shaft is .750 end to end, so that's good. The motor repair shop says it'll be...
Thanks Jim. I have a very highly rated electric motor repair shop nearby and I'll see what they say. New motor is $450! H hopefully cheaper than that.
That's what I was thinking. Thanks Wayne.
I haven't been able to find a unisaw three belt pulley with bushing.
I'm a little worried that the wobble in the pulley means the shaft has worn unevenly but I guess that could be the pulley hole worn out too.
Alright then. I found a motor repair shop that does machining too. I'll give them a call tomorrow. I'll use loctite on the set screws for sure. Thanks. I'll let you all know what happens.
Yes, it's rocking in the opposite direction the motor turns which is what I would expect. How does this happen? Is it because the set screws came loose at some time?
Yes brand new key just falls out and Pulley has wobble when tightened down and spun. I'll have to call around to find someone to repair this. Should I call machine shops or electric motor repair...
Okay let me have it, how bad is this and is it repairable or do I need a new motor!? :(
Thanks
Mike
404611
I checked this and the motor pulley is about 3.8". It hangs get shaft end about that much. I'll probably ask on OWWM, I'm not a member over there yet, and call Delta Monday.
I'm not finding anything that seems like it pertains to this model/type 34-801f, it's a 1987 vintage. There is adjustment on the blade guard/splitter bracket too. I read another post here about...
I've been looking for that tutorial. I felt there was more to it but just can't figure out the correct way. I'll do a search there, thanks.
I replaced the arbor bearings on my new to me unisaw. When I was pulling everything apart I noticed the arbor pulley and motor pulley were over an inch out of alignment. I figured I'd fix this upon...
Great suggestions! The pads are .095 worn out so I'm ordering .125 x .75 x 2 foot uhmw for $3! I should be able to make what I need from that. Thank you.
I broke a glide pad on my biesemeyer fence and thought I'd replace all the pads as some are quite gouged and very brittle. I can only find them for $5-12 each! Not sure I t to spend that much too vw...
Thanks to everyone for your input. I bought the saw, dust collector and outfeed table. I took the fence, rails, top, motor cover and motor out of the unit and it made it much more manageable. Man the...
Offered 950 for everything including the 4x8 maple outfeed table and dust collector and he accepted. I'm going to go take it all apart this week and he'll haul it to my place for me.
I asked if he could come down on price or otherwise entice me. He has a Delta 1.5hp canister and bag dust collector for sale too that he'll throw in with delivery to my place for 1100. I keep seeing...
FYI it's either this or a new $1000 table saw (maybe Grizzly G0771Z). I've been in the market and only have a cheap jobsite saw, no dado or nice blades.
You've pretty much confirmed what I was thinking, it's top dollar price. I think he is including a 6" Freud dado set and a couple other blades. He does have a Delta 1.5hp dust collector for sale too,...