Search:

Type: Posts; User: Bill Dempsey; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    1,050

    Turning epoxy

    I’ve repaired a bark inclusion in a peppermill head usung crushed decorative stone mixed into epoxy. It now appeard hss tools are not up to the turning task. Must i use carbide?
  2. Replies
    3
    Views
    1,068

    design of crushgrind based Peppermill

    I'm ready to start making 6 mills for holiday gifts, all based on crushgrind (or Woodcraft clone) mechanism. In the past, I've always included a mortise and tenon of various designs between top and...
  3. Replies
    10
    Views
    2,182

    Outdoor white oak table

    I'm building a bar height table and stools from white oak. It will reside in a screened in porch in coastal Florida, most of the time. Indirect sunlight, occasional rain.
    Thinking of finishing with...
  4. Replies
    13
    Views
    2,501

    Wow, thanks for taking the time, everyone. I...

    Wow, thanks for taking the time, everyone. I plan to call Doug (alt, Trent Bosch) tomorrow.
  5. Replies
    13
    Views
    2,501

    Bushing for Thompson handles

    Looking to find bushings for my Thompson 5/8 nose handles. Like to get to 1/2 and 3/8. Trying to get something off the shelf, avoid machining. Any help appreciated.
  6. Replies
    1
    Views
    963

    Turning in Ft Pierce Fl area

    I'll be spending quality time in Ft Pierce area for next 6 weeks or so. Zip 34949. Looking for
    Turning opportunities, active clubs, and the like.
    Any help much appreciated.
  7. Replies
    16
    Views
    1,982

    Closing the loop. This was Birdseye maple, I...

    Closing the loop. This was Birdseye maple, I used the climb cut router technique with pressure cawls. Result was great, no tear out or chipping.
    Thanks....
  8. Replies
    16
    Views
    1,982

    Edge Jointing Veneer

    Looking for best practice for edge jointing shop sawn veneer. Sawn to 3/32 or slightly thinner, going to drum sand to 1/16 for glue up. Birdseye and curly maple at the moment. Pieces are 45-48...
  9. Woodworking opportunities near Ft Pierce Fl

    looks like I'll be spending quality winter time in Ft Pierce Fl area (34949). Seems hard to find woodworking opportunities in the area. Local Makerspace appears closed now. Any ideas/help would be...
  10. Replies
    8
    Views
    1,776

    He recommended the regular 1/2 in spindle gouge. ...

    He recommended the regular 1/2 in spindle gouge. Next step would be 3/8 detail.
  11. Replies
    8
    Views
    1,776

    Update, I just talked to Doug. He got me on the...

    Update, I just talked to Doug. He got me on the right path straight away, what a great guy...
    No need for more
  12. Replies
    8
    Views
    1,776

    Thompson spindle gouge question

    Looking to upgrade my lathe tools, spindle gouges at the moment. Use would be general spindle turning of medium to
    larger items. Peppermills, goblets, tool handles and the like.
    I have D-way in...
  13. Replies
    7
    Views
    1,444

    Pepper/salt mill finish choices

    I'm making 8 pepper and salt mills for friends and family. Mix of crush grind and traditional mechanisms (my stock).
    Claro walnut, Sipo, and American hardwoods. In the past I've finished mills off...
  14. Replies
    4
    Views
    2,752

    Just to close the loop, Jamie’s input was...

    Just to close the loop, Jamie’s input was correct. The clearances are for the outside of the face frame. I actually called GE and confirmed it. Interestingly, on another forum there was discussion...
  15. Replies
    4
    Views
    2,752

    Jamie. thanks for responding. I noticed the...

    Jamie. thanks for responding. I noticed the "prepare" section. My plan is to have the oven simply sit on the deck of the cab, OK with that?
    The reason for my questions are based on my original...
  16. Replies
    4
    Views
    2,752

    Help with wall oven cabinet design

    First post in this forum, hope this is right place.
    I'm needing to design/build a face frame wall oven cabinet for pacement in an island. The oven is GE JTS5000SNSS, with the installation...
  17. Replies
    9
    Views
    2,067

    Sorry, cabs are face frame

    Sorry, cabs are face frame
  18. Replies
    9
    Views
    2,067

    Kitchen cabinet hinges/installation

    Not sure if this is the right place for the question, mods move if necessary.

    I'm usually a one off furniture builder, occasionally shop cabinets and such. I've got a relatively fully equipped...
  19. Replies
    6
    Views
    1,119

    Nice piece, looks great to my eye. What strength...

    Nice piece, looks great to my eye. What strength ammonia do you use?
  20. Replies
    10
    Views
    1,610

    Jointer planer choices

    I'm considering upgrading my griz 8 inch jointer. Seems combo machines are liked by many. With a budget of roughly 3k, it seems Jet jjp-12 and Grizzly are the options. Can anyone help with...
  21. Replies
    7
    Views
    3,884

    I note the differences in drilling the mill head,...

    I note the differences in drilling the mill head, 7/8 dia by crushgrind (and West), and 15/16 from craft supplies. I've made quite a few of these and find the "best for me" method is 15/16 dia and...
  22. Starrett.com shows a skip tooth in 1/2 24tpi. I...

    Starrett.com shows a skip tooth in 1/2 24tpi. I buy from them often, good prices, takes a week or so to make up the length needed, usually free shipping.
  23. Replies
    7
    Views
    853

    16 inch drum sander choices

    I'm in the market to replace my Delta 1832, still very functional, but lacking the newer conveniences. I find a 16/32 will fit my needs. Looking at Supermax and Jet. Any input will be much...
  24. Sorry Reed, spell Checker got me again....

    Sorry Reed, spell Checker got me again....
  25. Hi Robocalls, Maybe this set up block from Ron...

    Hi Robocalls,
    Maybe this set up block from Ron Brown
    https://www.ronbrownsbest.com/index.php?route=product/product&product_id=737
Results 1 to 25 of 68
Page 1 of 3 1 2 3