Search:

Type: Posts; User: Brent Ring; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    22
    Views
    9,663

    Superb design, and implementation! Congrats on...

    Superb design, and implementation! Congrats on being published in FWW.
  2. Well, I did get it completed, having to be be...

    Well,

    I did get it completed, having to be be patient, slow and methodical with the leveling and parallelism adjustments. I set the sliding table about .001-.003 above the cast iron table. And...
  3. I so appreciate hearing about your experiences...

    I so appreciate hearing about your experiences and I don't think you have hijacked the thread at all. I am still confused by the concept of why the sliding table does not need to have to be parallel...
  4. So priority is to get the sliding table level or...

    So priority is to get the sliding table level or close (+- .003 to .005), across the length of the sliding table, then worry about parallelism. I definately have a leveling job to do, as I noticed...
  5. Fixed table has a .002 to .003 dip on either side...

    Fixed table has a .002 to .003 dip on either side of the blade. Corners front to back are even, if sliding my dial guage works as a test. I have a aluminum straight edge that is 24"
  6. Why would I not want to try to get it zero over...

    Why would I not want to try to get it zero over the entire length of the slider? Grizzly says that it should be possible by using the miter slot.

    I also need to get it flat. Its a pain for...
  7. Replies
    26
    Views
    3,511

    We just ordered one with our logo. Excited to...

    We just ordered one with our logo. Excited to use it!
  8. Grizzly G0623x Sliding Table Parallelism Adjustment Frustrations

    All,

    I wasted nearly 8 hours yesterday trying to get my sliding table parallelism adjustment back into alignment. It started when I was checking my crosscut fence using the 5 cut method. The 4th...
  9. Replies
    50
    Views
    9,130

    My wife and I are starting to spend some more...

    My wife and I are starting to spend some more time together, building rocking chairs. She has had a bit of a epiphany for those that dont have a spiritual leaning, and a spiritual experience for...
  10. He must have not been very smart then :D

    He must have not been very smart then :D
  11. Need a new tension spring.... notice the one in...

    Need a new tension spring.... notice the one in is all compressed. Only has a 3/8" blade on it.
  12. More pics, lower wheel, foot brake, tension...

    More pics, lower wheel, foot brake, tension guage, upper wheel, back, and motor area.357698357699357700357701357702357703357704357705
  13. 357694357695357696357697Showing pics of power...

    357694357695357696357697Showing pics of power switch, overall machine, upper and lower guides.
  14. Here are the pics as promised. 357692357693

    Here are the pics as promised. 357692357693
  15. Well - Its mine - picked it up last night. ...

    Well - Its mine - picked it up last night. Talked him to $800. And yes - pics are coming. One thing I noticed is that the tension spring is very nearly completely compressed. It cut very well...
  16. How are parts for this saw? I have heard that...

    How are parts for this saw? I have heard that parts can be hard to come by. The saw runs well, and I might be able to get it for less than $900, but I am concerned about parts when things go bad. ...
  17. Powermatic Model 80 20" Bandsaw - Yes or No?

    All,

    I have been in the market for a bigger bandsaw. Starting to build some rocking chairs a la Hal Taylor, and my PM 141 does not have enough clearance to make a few of the cuts needed. A...
  18. Replies
    65
    Views
    11,827

    Favorites - Can't pick just one. Love The...

    Favorites - Can't pick just one. Love The Cowboys, and The Shootist, the Man Who Shot Liberty Valance, Man from Snowy River. One thats not a complete western in the traditional sense, but has Yul...
  19. Replies
    24
    Views
    3,683

    Hi Van, That is. "Turbo Fly" is the name of...

    Hi Van,

    That is. "Turbo Fly" is the name of the route. Its down in Maple Canyon, near Freedom Utah. https://www.mountainproject.com/v/turbo-fly/106757333. In the winter, it ices up just to the...
  20. Replies
    24
    Views
    3,683

    Well, the saw is back in action! I put a new...

    Well, the saw is back in action! I put a new Timberwolf 3/8" 4T blade on it, and followed guidelines to only worry about setting the gullets of the teeth on the center of the wheel, right on the...
  21. Replies
    24
    Views
    3,683

    Van, I did crown them. I watch a video on the...

    Van, I did crown them. I watch a video on the concept of aligning the gullet of the teeth on the blade with the center of the wheel. I am going to give that a try. I have always just centered my...
  22. Replies
    24
    Views
    3,683

    OK, here is where we are: 1. Replaced Upper...

    OK, here is where we are:

    1. Replaced Upper Wheel Bearings
    2. Replaced Urethane Tires with Glued on Rubber Tires
    3. Added a new Tension Spring
    4. Checked lower bearings - Did not require...
  23. Replies
    24
    Views
    3,683

    Threads look good!

    Threads look good!
  24. Replies
    24
    Views
    3,683

    Hi Mark, I can tell that the Urethane tires...

    Hi Mark,

    I can tell that the Urethane tires are crowned. It was a bear to get the tilt adjustment perfect to keep the blade centered. It would move forward or backward on the wheel if I did not...
  25. Replies
    24
    Views
    3,683

    I will give that a shots and get back to you!

    I will give that a shots and get back to you!
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4