Search:

Type: Posts; User: Paul F Franklin; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.26 seconds.

  1. There are several threads here about DIY...

    There are several threads here about DIY solutions for this. If you dags for "dust bin sensor site:sawmillcreek.org" you should find them. Most are variations on a commercial photosensor with a...
  2. Mike, I like your cart. I don't have a lot of...

    Mike, I like your cart. I don't have a lot of festool stuff, but I store the systainers stacked on shelves...and the one I need is always on the bottom:mad:

    I got my closet roll outs built along...
  3. Interesting....I have seen just the opposite. I...

    Interesting....I have seen just the opposite. I mostly shop at Giant Eagle here in NE Ohio, and many of the "national" brands have been replaced by GE branded versions. A lot of times the store...
  4. Replies
    13
    Views
    756

    The spiral compression bits are less likely to...

    The spiral compression bits are less likely to catch, but I use the robosander pattern sander in a drill press when dealing with end or squirrely grain. You can start with a coarse sleeve to remove...
  5. Replies
    13
    Views
    731

    The bales are pretty big, and they're also pretty...

    The bales are pretty big, and they're also pretty heavy. If you mean bus like a school bus, you have a chance. If you mean bus like a van....well I'd be looking at renting a truck or trailer to...
  6. Replies
    21
    Views
    1,170

    If the garage door is a typical sectional door...

    If the garage door is a typical sectional door that rolls up tracks (rather than a tilt-up or California door), you will probably have to bevel the edges of 2" foam to provide clearance when the...
  7. I finished up all the trim and installed the...

    I finished up all the trim and installed the closet doors in the hallway. I only have a few remaining tasks before I can call the current remodeling project done. I have to paint the inside of the...
  8. Replies
    16
    Views
    1,028

    Richard, The way I read it the OP's cabinet...

    Richard, The way I read it the OP's cabinet sides are bowing, not the drawer sides....
  9. Replies
    16
    Views
    1,028

    I agree with Jim. Even good side mount slides do...

    I agree with Jim. Even good side mount slides do not like to have the two halves pulled apart (or pressed together, for that matter). For smooth operation they need to have the correct clearance...
  10. We finally got a couple of long drenching rains...

    We finally got a couple of long drenching rains this week; we really needed it.

    I got the jambs and casing set on the hallway closet door and then sized the doors, test fit them and got them...
  11. Replies
    39
    Views
    2,741

    It doesn't sound like a fence slippage problem,...

    It doesn't sound like a fence slippage problem, even though many users have had to adjust the fence position lock so it locks more securely. If that were the problem you would expect a gradually...
  12. This looks really sweet, and you did a nice neat...

    This looks really sweet, and you did a nice neat job installing everything. Can you share a ballpark cost for all the "stuff", aside from your labor?
  13. My reinforcements to our blueberry enclosure have...

    My reinforcements to our blueberry enclosure have been effective against the birds, but the squirrels forced their way in and got a few berries before Mary spotted them and chased them away. I added...
  14. Replies
    12
    Views
    1,111

    For non-stick, we went with the Le creuset...

    For non-stick, we went with the Le creuset toughened non-stick series. They are PFOA free, but I assume contain PFTE. We've only had them a couple of months, but so far we love them. Work well on...
  15. IMO, the gaskets are the weak part of the V3000...

    IMO, the gaskets are the weak part of the V3000 design. They compress too easily and the plastic flanges deform over time causing small leaks. I've been gradually replacing the gaskets, usually...
  16. Replies
    23
    Views
    1,816

    Search for chipmunk bucket trap for a simple way...

    Search for chipmunk bucket trap for a simple way to trap them. But find out where they are getting in and take care of that or you will just get more.
  17. Nice looking shave horse Todd! Dennis, look...

    Nice looking shave horse Todd! Dennis, look forward to hearing how you like the grill.

    I finished the family room sheetrock repairs, wired up the new receptacles, and painted. Put up the new...
  18. Although the dewalt track is different, the...

    Although the dewalt track is different, the dewalt saw fits and works on Festool track (and I assume also on the other compatible tracks). I bought the dewalt tracks when I bought my saw, but have...
  19. The grass tiomos series hinges have three...

    The grass tiomos series hinges have three adjustable self closing force settings which makes it easy to compensate for door size and weight. I usually end up using the lightest setting for typical...
  20. Replies
    2,295
    Views
    346,069

    Sticky: I'd also be worried about what all the water...

    I'd also be worried about what all the water would do to my apartment when whatever they used as a lining fails and the water comes pouring in....
  21. I don't think there's anything you can inject...

    I don't think there's anything you can inject that will help much. You need fasteners that run through the Jamb into the framing behind it, whether it's wood or block or ?. Given that the jamb is...
  22. Replies
    12
    Views
    1,309

    My top is roughly like your version 2 without the...

    My top is roughly like your version 2 without the extension, maybe a few inches larger. It has worked well for me. I find that when work pieces get larger than can be comfortably worked on a top...
  23. I'll add a word of caution from my EE days. Once...

    I'll add a word of caution from my EE days. Once you enter the realm of capacitors used in electronic applications, meaning other than AC caps used for motor starting, there are factors beyond...
  24. Replies
    14
    Views
    1,152

    I have leap frog-ed my track by cutting as far as...

    I have leap frog-ed my track by cutting as far as I can, then butting a long piece of plywood with a straight edge halfway against the back side of the track so half of the plywood is against the...
  25. Don't think it matters much as long as you avoid...

    Don't think it matters much as long as you avoid anything with silicone in it. Johnson's paste would be easy to brush on with an acid brush or the like, or you could rub them with a block of...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4