Search:

Type: Posts; User: Kevin Jenness; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    2
    Views
    106

    Depends on the kiln design and thickness of...

    Depends on the kiln design and thickness of lumber in the load. My small kiln's outside dimensions are about 4' x 12' x 8' high and can hold around 600 bd ft.

    That seems like a pretty wide kiln....
  2. Aaron, pictures would definitely help. You may...

    Aaron, pictures would definitely help. You may have a weird batch of ribbon striped Swietania Macrophylla but it is not something I have run into. Your description sounds more like Khaya or possibly...
  3. Thread: Poplar

    by Kevin Jenness
    Replies
    34
    Views
    1,749

    Throw that book away. Old growth, slow grown...

    Throw that book away. Old growth, slow grown yellow poplar (Liriodendron Tulipifera) was rot resistant but not likely to be found on the market now. Similar to Eastern white pine in that respect,...
  4. Replies
    17
    Views
    651

    Looks good. The gridwork can be omitted if the...

    Looks good. The gridwork can be omitted if the foam is glued. I've used blueboard calibrated for thickness and epoxy in a vacuum press. 6mm marine ply skins, thick edgeband to accept hinge screws and...
  5. For sure stroke sanders are under-appreciated. I...

    For sure stroke sanders are under-appreciated. I would still have one if I had room. Takes some skill to use properly, but very productive, low energy use and can be had for low $. Fills the wide gap...
  6. Thread: Poplar

    by Kevin Jenness
    Replies
    34
    Views
    1,749

    It's inexpensive, easily worked,reasonably...

    It's inexpensive, easily worked,reasonably stable, available in long, clear cuttings and is readily stained. Not that appealing to my eye as a primary wood without disguise. I would never use poplar...
  7. An edge sander is a very useful tool for cleaning...

    An edge sander is a very useful tool for cleaning up edges and end grain, smoothing curves with either the platen or idle roller and final fitting of doors and drawer fronts. A good roi for a small...
  8. I really don't feature nails, especially hidden...

    I really don't feature nails, especially hidden ones, in a benchtop. I would glue up the top and fasten it from below with lags, construction screws or dry dowels allowing for seasonal movement.
  9. Pretty much the same starting point, 120 or 150 ...

    Pretty much the same starting point, 120 or 150 on a hand-held belt sander unless there's tearout. I have a 10* face bevel on my planer knives which helps. If I'm working with tearout-prone wood I...
  10. Replies
    6
    Views
    518

    https://www.youtube.com/watch?v=fhlMQr7Hk0k...

    https://www.youtube.com/watch?v=fhlMQr7Hk0k Straight from the horse's mouth.
  11. Replies
    18
    Views
    928

    Space is at a premium in my shop so when I build...

    Space is at a premium in my shop so when I build cabinets the flatwork comes first - face frames if any, trim, doors, drawer fronts and drawer parts,, then prefinishing, then carcass parts. Cases and...
  12. Replies
    18
    Views
    928

    If you are using manufactured drawer slides and...

    If you are using manufactured drawer slides and can work to the necessary tolerances it doesn't matter which comes first. You should always have the hardware in hand, or at least detailed specs and...
  13. My mistake. Thanks for setting me straight.

    My mistake. Thanks for setting me straight.
  14. AC pumps are typically very high vacuum low...

    AC pumps are typically very high vacuum low volume units. For veneer pressing you want a pump that will draw at least 2cfm at >20" hg.
  15. A piece of melamine coated particleboard under...

    A piece of melamine coated particleboard under the layup, atop the grooved base platen.
  16. There are differing ways of setting up and...

    There are differing ways of setting up and operating a vacuum press. I started out with and still use Daryl Keil's setup with a grooved 3/4" base platen made of melamine coated particleboard inside...
  17. If you can get that vlt setup in running order...

    If you can get that vlt setup in running order for a decent price go for it. If stored out of the light the bag should be ok. The pump shown on the vlt site is a Gast rotary vane similar to mine and...
  18. I used my son's Milwaukee cordless chainsaw...

    I used my son's Milwaukee cordless chainsaw recently and it worked well but you have to keep the chain sharp and be patient. There's a big difference in power between a high end cordless saw and my...
  19. Vacupress is a reliable source for pumps and bags...

    Vacupress is a reliable source for pumps and bags as well as advice. Daryl Keil knows as much about vacuum pressing as anyone and the forum on their site, although not that active, is a valuable...
  20. Replies
    49
    Views
    3,168

    Recently my ancient lathe task light failed to...

    Recently my ancient lathe task light failed to turn on. After checking the bulb I jumped to the conclusion that the switch was bad and started to dismantle the fixture. Turned out I had accidentally...
  21. Lyle Jamieson "gets by" with a chainsaw, no doubt...

    Lyle Jamieson "gets by" with a chainsaw, no doubt you can too. I wouldn't like to be without a bandsaw, for turning blanks and many other tasks, but I "get by" with one, although I understand four is...
  22. Replies
    9
    Views
    596

    As Aaron noted this seems to be a fairly common...

    As Aaron noted this seems to be a fairly common issue. Jointer tables are meant to be flat, but how flat do they need to be? If you are getting acceptable results, don't worry about it.
  23. Replies
    7
    Views
    512

    If you cut the pins flush it will make clamping...

    If you cut the pins flush it will make clamping easier. Use cauls with some give like leather or soft pine combined with a glue resist layer like wax or plastic film.

    If the box joints are fit...
  24. Replies
    13
    Views
    756

    Saw as close to the line as possible and trim...

    Saw as close to the line as possible and trim with the grain direction with a sharp spiral or segmented cutter. Or saw and sand with sharp abrasives. There are pattern sanding heads available.
  25. Replies
    9
    Views
    927

    Paste wax.

    Paste wax.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4