I keep a Battery Tender on the start battery on my generator. The battery was made in 2009. Started generator first of the month, on monthly test run. In case of battery failure, and to start...
Type: Posts; User: Bruce Wrenn; Keyword(s):
I keep a Battery Tender on the start battery on my generator. The battery was made in 2009. Started generator first of the month, on monthly test run. In case of battery failure, and to start...
There are hundreds of videos showing how to rescue a 12volt battery. Epson salt, baking soda, welder for charging, battery boost charger slow charging. etc. But has anyone here actually been...
Got one once for a large purchase on my Amazon card. Only one problem, I didn't have an Amazon card.
Same thing with Rayovac batteries. Threw out a couple of boxes of them. One was a replacement purchased with coupon to replace another leaking box. Now I buy either Costco's Kirkland brand, or...
Years ago, FWW ran an article "The Little Blade That Could." It was a 1/4", 6TPI, hook pattern, 0.025 bi-metal blade. Ran one for 14 years cutting out Toy's for Tot's car bodies.
Remember that old Sears RAS you couldn't wait to get rid of.. Louver shops had a pair set up for right and left cuts. As for fans lasting, did they get oiled annually? New ones have a "one time"...
Here local county only sends a bill if it's over five bucks. I own three multiyear licensed trailers. Tax is collected at renewal, but because there is no renewal, in the past they charged no tax,...
We built our house in 1980. In January, 1981, started on detached garage. First of February, tax man showed up and wanted to know why we didn't list garage, as it had to have been built before...
I would start at the source, chlorinate the well. Turn off energy source to WH. Run system till you smell chlorine at faucet, both hot and cold. Let sit for 24 hours, and then flush system.
The cars knocked over were most likely empties, not loaded.
I prefer the two cut method. Remember it's woodworking, not machinest work.
Spent several hours changing plugs and wires on my 94 Ford Areostar. Wouldn't wish the job on my worst enemy, but had to be done. Ordered a new set of tires for same van. Fed EX ground left them...
Instead of spray welding, why not build area up using MIG welder, and then turn down to size.
I have two cookers made from 275 gallon oval oil barrels. Both can use either gas, charcoal, or wood coals. Both have double grates which makes it easy to turn a hog or rack of chickens over. Each...
Wife's car, not many. Same with tires. My truck and van, 2-3 hundred thousand miles. On my old Honda Civic, I had a couple tires that went over 100K miles.
Generally only lend to a couple friends. Most often, just go over and do needed job. Used to have a 20# sledge hammer. Only lent it out once, and borrower brought it back next day saying he bought...
Check out 1018 cold rolled flat bar, 3/8 X 1 inch size. Four foot length from Metals Depot is about $25.
Check out Taylor tools sharpening system for straight edge tools. Less than fifty bucks for complete system, plus cost of drill press.
Went to friend's beach house to fix dryer outlet, which wasn't wired correctly years a go. Worked on ice dam in bottom of her Sanyo refrigerator, plus got ice maker working. Changed oil in van. ...
Local Costco goes thru an average of 30,000 gallons a day, which translates into five tankers a day. Only by luck will you be there when there isn't a tanker dumping during open hours, I have seen...
Also make sure chisel point of nail runs across edge of MDF, not parallel to edge.
That's why they are moving to North Carolina. You never own any property, only rent from local taxing body. Miss one payment and you are on the street.
Drill double pocket screw holes, then use pocket screw clamp in one to hold frame in place while driving the screw in the other hole.
Our biggie is no well on this lot. Twenty five wells in neighborhood, only two of which produce over a gallon a minute. That means only an 8% chance of hitting enough water on first try, with a...
Mine was over a quarter million. Now my corrected tax value is less than it was four years ago, which means I have been over paying for the last four years.