Search:

Type: Posts; User: Lee Schierer; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.66 seconds.

  1. Replies
    2
    Views
    258

    Check your drive belt tension, it could be the...

    Check your drive belt tension, it could be the belt is slipping when you hit harder sections of the wood.
  2. Replies
    22
    Views
    913

    No offense Jim, but you aren't old enough to have...

    No offense Jim, but you aren't old enough to have used one like that.

    Do a search for "antique spoke adjuster" and you will see many examples. My grandfather had one that he used.
  3. Replies
    11
    Views
    296

    We have a timer on ours and it used to help save...

    We have a timer on ours and it used to help save cost because there used to be an off peak rate and special meters that tracked on peak and off peak use. Because we are total electric including all...
  4. Replies
    11
    Views
    413

    Nice looking mailbox. Hopefully the postman will...

    Nice looking mailbox. Hopefully the postman will use it since it an official postmaster approved box.
  5. Replies
    14
    Views
    1,551

    Looking good.

    Looking good.
  6. Replies
    1
    Views
    82

    I don't think there are any standards other than...

    I don't think there are any standards other than normally the thinner drawers are at the top and the deeper drawers are at the bottom. Since it is a kitchen determine what is likely to be placed in...
  7. Replies
    22
    Views
    913

    I believe the small tool with the wing nut...

    I believe the small tool with the wing nut located between the Marsh Plane and the saw vise is a spoke adjusting tool for a bicycle or motorcycle.
  8. Replies
    5
    Views
    274

    Interesting design with holes in the doors....

    Interesting design with holes in the doors....
  9. Replies
    14
    Views
    748

    I agree with Mike. However, if you can blow out...

    I agree with Mike. However, if you can blow out the fan end of the motor with compressed air first it would clear any dust of of the switch.
  10. The SMC search function leaves a lot to be...

    The SMC search function leaves a lot to be desired. Open another tab and use google for the same search it will find SMC posts that are relevant.
  11. Thread: Roundover

    by Lee Schierer
    Replies
    7
    Views
    324

    Coincidently, I'm working on a night stand with a...

    Coincidently, I'm working on a night stand with a design similar to the table you showed in your post. I made a little champfer plane that I use to break the corners that I'm not rounding over. The...
  12. Replies
    34
    Views
    1,160

    I'm 71, don't tell anyone...The problem with...

    I'm 71, don't tell anyone...The problem with Craftsman radial arm saws (and most others) is accuracy and repeatablity. The reason you see cuts at angles in the tables is that for cleaner cuts you...
  13. Replies
    7
    Views
    306

    My phone uses Drive pdf viewer or Samsung notes.

    My phone uses Drive pdf viewer or Samsung notes.
  14. Replies
    10
    Views
    442

    Some wood processor formats do not play well with...

    Some wood processor formats do not play well with the Vbulletin software. You may see all sorts of extra weird characters in your text when you post it. Remember you can edit your post for 24 hours.
  15. Replies
    34
    Views
    1,160

    I still have the original motor on mine. About...

    I still have the original motor on mine. About once a year I pull the little plastic caps over the bearings and add a few drops of oil. My motor is 1 Hp and I find it adequate for all the cutting I...
  16. Replies
    34
    Views
    1,160

    I've had my 113 saw for over 30 years and I did...

    I've had my 113 saw for over 30 years and I did the alignment about 5 years after I got it. I checked it a couple of years ago and it had moved maybe 0.002 according to my dial indicator. I rarely...
  17. Replies
    12
    Views
    530

    I'll take one. I need to think about replacing...

    I'll take one. I need to think about replacing the door to my shop from the house. Very nice work.
  18. Replies
    34
    Views
    1,160

    My saw is a 113.298720. I would definitely...

    My saw is a 113.298720. I would definitely recommend changing the pulleys. It has been too many years to recall where I got mine. What you want are machined pulleys of the same diameter and hole...
  19. Replies
    34
    Views
    1,160

    What is the model number of your saw? I have a...

    What is the model number of your saw?
    I have a Craftsman 113 model saw with the cast iron open grate wings. I have tuned my saw, added a Beismeyer fence and a Kreg crosscut guide. I also replaced...
  20. It works great on cars, generally I avoid having...

    It works great on cars, generally I avoid having any amount of silicone near my woodworking. I have personally observed fingerprints on painted surfaces caused by residual silicone remaining on...
  21. Replies
    20
    Views
    647

    When I added additional insulation to our house,...

    When I added additional insulation to our house, I noticed that the added insulation was blocking the air flow from the perforated soffet into the attic. Since the area was almost impossible to get...
  22. Replies
    49
    Views
    1,929

    Having lived in that part of the country the most...

    Having lived in that part of the country the most likely answer is, most houses in Texas are built on a slab of concrete. They were not built with sustained freezing temperatures in mind. Pipes are...
  23. After giving it some additional thought, I am up...

    After giving it some additional thought, I am up over 75 projects in my home. That doesn't count multiple items like picture frames, wood toys, curtain rods and brackets where I made several at the...
  24. Replies
    7
    Views
    426

    I sometime use my phone for taking photos of...

    I sometime use my phone for taking photos of things. I transfer those photos to my lap top via blue tooth. That allows me to check the photos for proper orientation before posting them on SMC.
  25. Replies
    6
    Views
    463

    Nice work so far. Hopefully you checked the...

    Nice work so far. Hopefully you checked the local building codes for maximum and minimum dimensions for your handrails.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4