Search:

Type: Posts; User: Earl McLain; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    274

    Wow…if I lived closer I’d make you some nice new...

    Wow…if I lived closer I’d make you some nice new caulk and trade you for the mahogany! Best wishes on Your project!
    earl
  2. Today’s nail polish removers may not have any...

    Today’s nail polish removers may not have any acetone in them at all. And, they may have some moisturizers that are great for fingers but might make it tougher to get a good finish. Good to have a...
  3. Replies
    9
    Views
    682

    One of these could be possible as well. steering...

    One of these could be possible as well. steering wheel knobs | McMaster-Carr
    Before there was power steering--people used them in cars!!
    earl
  4. Replies
    32
    Views
    1,933

    Yeah, since the swallows that carry the coconuts...

    Yeah, since the swallows that carry the coconuts are not regulated in their travels, coconuts should be in good supply!!
    earl
  5. Replies
    5
    Views
    878

    @Dean Perkins--have you found the minimum speed...

    @Dean Perkins--have you found the minimum speed of 500 rpm to be any problem? Seems pretty fast for sanding or finishing on the lathe. Or drilling a lot of stuff too, for that matter.

    Chris--see...
  6. Replies
    11
    Views
    988

    I don’t use much stuff from Rockler, but have...

    I don’t use much stuff from Rockler, but have found their Dust Right fittings to work very well for moving my single hose between machines. The fittings with a Fernco style end (might actually be...
  7. I’m not likely to become homeless, but that’s a...

    I’m not likely to become homeless, but that’s a very tempting thought!!

    @ Dave Mount—awesome series, thanks for taking the time to do that!!
    earl
  8. Replies
    32
    Views
    2,671

    I've spent a few years trying to decide between...

    I've spent a few years trying to decide between the Miter Express and the Miter 5000. I've used the Dubby--and it's very good. But--my Incra stuff has been absolutely top-notch.
    earl
  9. Replies
    17
    Views
    1,242

    I’ve made a few that were okay-ish, but I...

    I’ve made a few that were okay-ish, but I splurged on the old version of the Jasper 200–nice tool. Don’t use it a ton, but it does exactly what it says.
    earl
  10. I don't know the cause, but $319 divided by $284...

    I don't know the cause, but $319 divided by $284 is about an 8.5% increase on my calculator. Still large for a year, but not 25%--yet!!
    earl
  11. Replies
    5
    Views
    694

    Dave--it may be helpful if you can figure out how...

    Dave--it may be helpful if you can figure out how to attach a picture of what fell out. If it's the Morse taper that the chuck attaches to, it could be as simple as cleaning both the male & female...
  12. Replies
    14
    Views
    965

    Here's the "Why not Wen?" thread:...

    Here's the "Why not Wen?" thread: https://sawmillcreek.org/showthread.php?291641-Why-not-Wen

    I've used a Dewalt 735 with Byrd head for several years, probably 200-300 bf/year. Probably time to do...
  13. Thanks Dave--i've thoroughly enjoyed the first 2...

    Thanks Dave--i've thoroughly enjoyed the first 2 installments. Enjoy your straight-forward writing style!!
    earl
  14. Replies
    7
    Views
    574

    I don't know if it's suitable--but every time i...

    I don't know if it's suitable--but every time i look at that hardware i think of the symmetry of using Kentucky Coffee Tree.
    earl
  15. I wish i hadn't read this. I've lusted for a WP...

    I wish i hadn't read this. I've lusted for a WP DP table for several years. The one i built 10 years or so ago was clunky, then there was an old Rockler table with the used DP that replaced my...
  16. Replies
    18
    Views
    1,013

    Also, check OWWM.org for "ruckering" or "rucker"....

    Also, check OWWM.org for "ruckering" or "rucker". Lot of folks get Old Arn moved that way through there--i'm not one of them though. Google search using that term is not helpful--but some of the...
  17. Replies
    17
    Views
    1,419

    Since you have to trim the 11 x 14 sheets...

    Since you have to trim the 11 x 14 sheets anyway--no harm in building a jig or two as Stewart suggested and trying the table saw and/or bandsaw. I'm thinking the bandsaw might surprise you.
    earl
  18. Replies
    13
    Views
    1,024

    Good looking boards. I don't have the answers to...

    Good looking boards. I don't have the answers to your questions--but i'm wondering if the heat generated by the tubes might influence the opinions of those with experience. That would create more...
  19. Replies
    3
    Views
    514

    There's a part of me that hopes you are right. ...

    There's a part of me that hopes you are right. Well...most of me hopes that. Then there's that little bitty piece of sanity that knows i'll spend way too much money if that happens!!

    Great score...
  20. Splinters. Painful little buggers that are...

    Splinters. Painful little buggers that are almost too small to pick out. Not a surface i'd want for a workbench. Made a great deck though, and an excellent table base for another deck. (local...
  21. Replies
    13
    Views
    7,111

    Woodturningz.com carries at least one version in...

    Woodturningz.com carries at least one version in a few platings. I agree with the earlier post--thought CS USA had them, but i didn't see it either.
    earl
  22. Great switch Lee, do you recall where you found...

    Great switch Lee, do you recall where you found that? Simple emergency stop without having to rewire.
    earl
  23. Replies
    12
    Views
    1,584

    Hickory and Oak Sawmill in Decatur, MI usually...

    Hickory and Oak Sawmill in Decatur, MI usually has both red & white elm, current price is showing as $3.25/bf for 4/4 and $4.00/bf for 8/4. Don't know if Steve is set up to ship--but he cuts & kilns...
  24. The bushings look too big to fit dog holes--but...

    The bushings look too big to fit dog holes--but hard to tell from the picture. Shop made or home brew--almost for sure. The bushings look like they might expand a bit when the end screw is...
  25. Matt--those extrusions look like 80/20 (company...

    Matt--those extrusions look like 80/20 (company is based in Columbia City, IN--west of Fort Wayne, and right on US 30). The fittings look like something they carry--but i don't know what they are...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4