Search:

Type: Posts; User: Izzy Camire; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    965

    Thanks Paul I will give this a try. I do not...

    Thanks Paul I will give this a try. I do not think I have the moisture problem though.
  2. Replies
    9
    Views
    965

    Painting concrete shop floor

    Hay Folks,
    Well the priming OSB topic had helpful answers so I thought I would try it again.

    I am thinking of painting the concrete floor in m shop. I have looked a little into Waterborne Epoxy...
  3. Replies
    19
    Views
    1,394

    Well I bought Kilz original and started putting...

    Well I bought Kilz original and started putting it on today. Wow this stuff is really disappearing into the OSB. I figure I will not get much more than 220 sq ft per gallon on coverage.
    Very nice to...
  4. Bora / Affinity Tools customer service

    Wow I am starting 2 threads in one week...better check perhaps the sky is falling eh!

    In my other tread I spoke about painting my shop to do this I need to move things and that included my small...
  5. Replies
    19
    Views
    1,394

    What Jim mentioned about low humidity in the shop...

    What Jim mentioned about low humidity in the shop is correct. In addition I put this up by myself and I figured the weight of it was considerably less than sheet rock. At this point it has been up 4...
  6. Replies
    19
    Views
    1,394

    https://www.sherwin-williams.com/painting-contract...

    https://www.sherwin-williams.com/painting-contractors/products/problock-interior-oilbased-primer
    Thanks for all the replies. It seems like there is some leeway it what can be used. The above link...
  7. Replies
    19
    Views
    1,394

    Priming OSB

    Hi Folks, I am getting ready to paint my shop. The first step will be to apply primer to the OSB. I have the rough side out so no waxy stuff to worry about. Just wondering if anyone has done this and...
  8. Replies
    25
    Views
    1,587

    Congratulations now you can work on the things...

    Congratulations now you can work on the things you want to do.
  9. Replies
    29
    Views
    2,066

    I also use Duckduckgo and like it.

    I also use Duckduckgo and like it.
  10. Replies
    9
    Views
    812

    Mark, welcome this forum is a great place to...

    Mark, welcome this forum is a great place to learn. Folks here always have good suggestions for problems.
  11. Replies
    8
    Views
    783

    Hmmm move to AZ have to think on that! After...

    Hmmm move to AZ have to think on that!

    After more thought the paste wax with thinner sounds easy to give a try.
  12. Replies
    8
    Views
    783

    Thanks for all the ideas. The flax oil seems...

    Thanks for all the ideas. The flax oil seems promising to me.
  13. Replies
    8
    Views
    783

    Vise handle

    Hi Folks,
    I was wondering what those of you with a Benchcrafted vise and a shop that is not climate controlled have done on the vise handle to prevent rust. Benchcrafted manual suggests linseed oil,...
  14. Replies
    5
    Views
    1,191

    There was a value in the menu system that was 400...

    There was a value in the menu system that was 400 and it should have been 320. I am not sure where it was located in the menu. Wish they had put some thing on their website.
  15. Replies
    5
    Views
    1,191

    We finally got Laguna tech support on the phone....

    We finally got Laguna tech support on the phone. They knew right away what the problem was. I guess they saw it before.
  16. Replies
    5
    Views
    1,191

    Yes Ted you are correct it is off 2.5" on the 10"...

    Yes Ted you are correct it is off 2.5" on the 10" Y dimension.
  17. Replies
    5
    Views
    1,191

    Laguna IQ offsetting dimensions

    Hi Folks,
    We are trying to get the IQ to run a simple program correctly.

    The program locates 2 holes at:
    X: 4.0 Y: 1.0
    X: 4.0 Y: 10.0

    We have an origin setup at the corner of the work...
  18. Replies
    31
    Views
    2,199

    A year ago we installed a Delta Cassidy that we...

    A year ago we installed a Delta Cassidy that we are very happy with.
  19. Replies
    17
    Views
    1,283

    Well I finally got back to the shop. I decided to...

    Well I finally got back to the shop. I decided to take the advice offered in this thread. On both infeed & outfeed tables I put the edge closest to the planer bed at exactly the same height as the...
  20. Replies
    17
    Views
    1,283

    I got out to the shop for a few minutes this...

    I got out to the shop for a few minutes this afternoon. I turned the planer over and the casting is fine no problems. There is no access to the planer bed from there. Tomorrow I will readjust the in...
  21. Replies
    17
    Views
    1,283

    Thanks to everyone for their responses. I have...

    Thanks to everyone for their responses. I have picked up a few ideas and will look into them later in the day and make adjustments.
    I will start by turning the planer upside down and look at the bed...
  22. Replies
    17
    Views
    1,283

    I went to the Woodcraft and on their 735 the bed...

    I went to the Woodcraft and on their 735 the bed does not flex up and down. I this has a lot to do with the snipe. Could it have come unglued or something?
  23. Replies
    17
    Views
    1,283

    Dewalt 735 issue

    Hi Folks,
    I am having a snipe issue with my 735. I have the Dewalt infeed/outfeed tables. I have adjusted them so the outfeed table is above the planer bed and the far end of it is higher yet. My...
  24. Replies
    24
    Views
    1,675

    I have them on my saw and what has been said...

    I have them on my saw and what has been said about setting them before the fence is set is true. With that said I like them and feel safer and I feel the cut is better for using them. I would buy...
  25. Replies
    9
    Views
    692

    I tried to get a new belt at Applied Industrial...

    I tried to get a new belt at Applied Industrial and they could not get it. I called an online place but he could not get it but he did pass on some info. The belt on my machine is a Deyun Belt...
Results 1 to 25 of 249
Page 1 of 10 1 2 3 4