Search:

Nordic Saw and Knife, Turlock CA.
They sharpen Diamond, Carbide, hand saws and [I think] band saw blade. They also make outstanding cutting tools .
https://www.nordicsaw.com/

Try 'Knothead' in Ceres CA. Or put 'lumber mills Ceres CA' into your search engine or go to Youtube and search for 'Knothead'.

The correct way to permanently install heavy machines is as follows:
[1] Position the machine in it final location.
[2] shim into perfect level
[3] install epoxy anchors into the concrete floor,...

Amen! to the form release. just had to grind 3/4" melamine board from a project. Ugly job! And I use form release.
Advice....
GET THE BEST FORM RELEASE YOU CAN FIND.
APPLY PROPERLY.
REMOVE...

Absolutely, keep both. 9'' is great with the 5/16"-3/8" blade. 14 " with the 1/2"-3/4"
I have three. 10", 14" & 18". All are dedicated to different tasks. Seldom change blades.

I installed three overhead reels for air in my 1800 sq ft shop. They were great. Wish I had installed several more. Also installed 4 electric power reels, [110].
In my new, but significantly...

I, too, was put off by the $$$ of the L-N screw drivers. But I do have a collection of L-N planes, and find regular screwdrivers are messing with the beauty of the L-N tools.
When complaining to...

I have created a similar 'carousel' tool cart. I started with a heavy base and then added about 50# of sand. Then 3 round shelves build on a commercial 12" d lazy-susan ring. The whole thing is...

YES< YES< YES. One of the best tools in my shop. Low for cabinets/large projects. High for smalls, carving, special hand tools.
10 years ago, I purchased a motor-cycle/snowmobile lift. Mine was...

I just was reading in another thread, where a fellow Creeker told of the number of his project in one room of his home. I stopped to count my projects in our home and was amazed. I counted 82! ...

To get a 're-sawn' look to a board, use a band saw. However, you do not want to feed the wood into the bandsaw as you would do when normally cutting. You will want to drag the face of the wood...

I created a pair of ply-wood jaws and covered them with 'Glove' leather. I've used them for 5+ years, and I still use them. They protect the tender item, increase the grip on 'odd shaped' items and...

Just my two cents............
I've owned several band saws.
Delta Homecraft 10', 1/2 hp, [not a bad LITTLE saw, but a little saw]
Delta 14", 1 hp, [good and dependable, a well know and respected...

Aura hardwoods is a supplier to many wood sellers, lumber yards, and many processor/manufactures of cabinet, furniture and similar.
They sell to walk in customers. you walk thru building, push their...

The sawyer in Rochester WA. [south of Olympia] is Bill Betts. Easy to find him on line. Nice guy, knowledgeable, fair. Give him a call.

Be cautious. Many manufactures have two or three levels of quality within their battery powered tools line up. The ones for sale at the Big Box Store, seem always to be the occasional use...

Yes!, I'd love to have the mobile base.

What make/model/caliber of gun did you use?

Were you wearing a mask? Have a gun?

I purchased the LT16 direct from Laguna in about 2006 or 7. It was a show demonstrator. It was shipped common carriier. I decrated it, set it up and started using it that day. There has never been...

When steam bending, it is best to use 'Green' wood. That which has been kiln dried will resist steam bending. To get around the kiln dried wood and use it for steam bending, it will be necessary...

Twice, I let one of my LN planes get damaged. Twice, I called LN. Twice is was told to send in for complimentary repairs. Twice they paid the return postage. Twice, they refuse payment.

These are...

Chair makers use large rubber bands that are made for the assembly/gluing process. The rubber bands I use are about 36" in length. They can be wrapped around the standard chair several time. If...

Wife!
When I am done with a project, she always has another!

Wood magazine's 'Weekend With Wood' event, scheduled for mid May has been rescheduled for Oct 29-Nov 1, 2020. I have attended several years and was looking forward to this year. However, I will not...