Search:

Type: Posts; User: Larry Cronin; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. I have a complete overhead setup that may need a...

    I have a complete overhead setup that may need a new home. I also live in NE Mass. so maybe local pickup.

    What do you want to spend?

    Larry Cronin
  2. Replies
    12
    Views
    850

    Thanks for the help I think I know the issue...

    Thanks for the help

    I think I know the issue that is causing the twist.

    I try the sanding or plane method to flatten the bottom.

    Larry
  3. Replies
    12
    Views
    850

    I realize I did a terrible job of asking my...

    I realize I did a terrible job of asking my question.

    What I was looking for is some help in approaching the situation.

    Do I start by sanding the part of the crib that touch till I get all...
  4. Replies
    12
    Views
    850

    I should have better described it. That piece in...

    I should have better described it. That piece in the photo goes on a base that has rockers attached to it.

    So it would need to be flat on the bottom to connect to the base.

    Larry
  5. Replies
    12
    Views
    850

    Help flattening a doll crib

    Hello

    I made a couple doll cribs and I did something wrong and they are not "flat". I am hoping that someone out there can give me some guidance on how to solve the issue. I am nervous that if I...
  6. Replies
    12
    Views
    1,010

    Thanks for replies. I missed that sale. In my...

    Thanks for replies.

    I missed that sale. In my next life I am going to pay more attention.

    Larry
  7. Replies
    12
    Views
    1,010

    Bessy Clamps at Home Depot

    Hello,

    Anyone have any experience with these Bessy Clutch Clamps? GSCC2.506 and GSCC2.512. They are at HD for $25 for a 4 pack, 2 6 inch and 2 12 inch.
    Seems very affordable for my type of...
  8. So I messed arounf a bit and tried a few...

    So I messed arounf a bit and tried a few different things suggested here.

    THe one thing I did not try yet was to champfer the holes. I dont have a champfer that big and my champfer bit for my...
  9. Thanks for all the suggestions. I will try a...

    Thanks for all the suggestions.

    I will try a bigger hammer and also I am going to try and rough up my holes and see if that helps.

    I will report back in a day or so.

    Larry C
  10. Help with Gramercy holdfast technique - they are not holding

    Hello,

    I built my workbench with lots of advice and knowledge from here.

    Came out really good and works great.

    But

    I cant get my holdfasts to work at all.
  11. Just to wrap it up. I had a some trouble...

    Just to wrap it up.

    I had a some trouble locating both the 7 inch and 8 inch outside vents that were readily available.

    So I am going with the 7inch to 6inch reducer and see how it works.
    ...
  12. Thanks for the suggestions. I am going to look...

    Thanks for the suggestions.

    I am going to look around a bit today and see if I can find some 7 inch stuff.

    If I can and it looks like it may work I might go with that. If it involves ordering...
  13. Duct hose suggestions for venting a Laguna 7 inch collector outside

    Hello,

    I have a Laguna 2HP manual clean dust collector (MDC0560-0145) that I am going to vent outside. Who knew besides those that read the manual or measured the outlet pipe that it is 7 inches....
  14. I was thinking of doing my glue up in the one...

    I was thinking of doing my glue up in the one board at a time method. I work from home and could get a few boards done in a day.

    I am still in the hunt for a No 7 plane.

    Thanks again to all of...
  15. I was not clear my no 9 is a Stanley 9 1/2 block...

    I was not clear my no 9 is a Stanley 9 1/2 block plane.

    I am looking at adding a 7, started the search for a used one initially.
  16. I do have a few hand planes which I am trying to...

    I do have a few hand planes which I am trying to use more and more. I own a No. 9, No 4, and a No 62.

    Thanks very to all of you for the suggestions and encouragement.

    If all goes well I will...
  17. Thank you all for the suggestions and...

    Thank you all for the suggestions and encouragement.

    I have to get started before I convince myself that I should wait and look at buying again.

    Larry Cronin
  18. Advice on building a workbench with my current equipment

    Hello,

    I am thinking of building a workbench, I cant bring myself to buying one.

    The size would be roughly be 26" by 65". Bigger will not fit in my shop.

    I plan to make it out of hard...
  19. Sorry I got side tracked with Thanksgiving. ...

    Sorry I got side tracked with Thanksgiving.

    Thanks for the suggestions and to Dom Greco, thanks for one of the best write ups I have ever seen. Photos, links, and a wiring diagram.

    At my house...
  20. When I looked at the iVac I was adding in the...

    When I looked at the iVac I was adding in the cost of also buying the auto switch for each of my tools. So at $80 plus $60 a tool it was costly.

    I think I am leaning towards the PSI one you...
  21. That looks pretty cool but it may be more than I...

    That looks pretty cool but it may be more than I want to spend.
  22. Aftermarket remote control for Laguna 2HP dust collector

    Hello,

    Has anyone found an aftermarket replacement for the Laguna remote control. Mine died and I was hoping to get something a little more robust.

    Should I just go and get a remote switch...
  23. Replies
    12
    Views
    14,652

    General Metalworking Hello, I just wanted to follow up and let the...

    Hello,

    I just wanted to follow up and let the thread know what I did. I ended up having a local sheet metal shop make them for me. They were $6 a piece using 1/4" stainless rod. I just never ...
  24. Replies
    12
    Views
    14,652

    General Metalworking Per your suggestion I am planning on going to a...

    Per your suggestion I am planning on going to a metal supply place this week.

    Thank you to all for the replies. It has been very helpful.

    I will let you know how I make out.

    Larry C
  25. Replies
    12
    Views
    14,652

    General Metalworking Thank you for all the suggestions. I may...

    Thank you for all the suggestions. I may purchase some 1/4 steel rod and see if I can figure out how to bend it with some consistency and relative ease. I have a stupid question, is cold roll steel...
Results 1 to 25 of 28
Page 1 of 2 1 2