Search:

Type: Posts; User: James Minick; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    3,541

    I have similar issues with both CO2 and Fibre...

    I have similar issues with both CO2 and Fibre units. You might adjust focus up or down to see if you can tone down the beam at your lowest setting that you can achieve firing. Hope it helps.
  2. Replies
    2
    Views
    2,419

    432518 Definite pucker factor when mom hands you...

    432518
    Definite pucker factor when mom hands you a JA charm bracelet with a dozen names to put on different charms. Calls them "her babies".
  3. Replies
    8
    Views
    1,709

    Going to be trial and error. That's the best...

    Going to be trial and error. That's the best advice I can give for right now.
    Even the different firearms and accessory materials are different. Glock v.s. Ruger or Magpul v.s. MFT.
    You can...
  4. Replies
    8
    Views
    3,629

    Thanks! It makes duplication of parts a snap. I...

    Thanks! It makes duplication of parts a snap.
    I was skeptical at first, but saw a pretty good demo with a pistol grip design.
    Figured I would give it a shot. I thought I had purchased a camera...
  5. Replies
    8
    Views
    3,629

    LightBurn and Cameras

    Due to issues, the LightBurn folks are out of cameras.
    Don't let that stop you!
    The camera addition is the best thing since pockets on shirts!

    I have a 100w Chinese Laser, red & black, Ruida....
  6. Don't know if you were able to get this figured...

    Don't know if you were able to get this figured out , but I'll give you a few tips:
    You will need to locate the motor controller usually lower right-side panel428779
    Should be a connector (loose)...
  7. Replies
    4
    Views
    5,036

    I run a 100w CO2, 50w Fiber, blower, computer...

    I run a 100w CO2, 50w Fiber, blower, computer with 2 screens, 4 lights, and stereo on the same circuit.
    Killawatt says 12A
  8. Replies
    5
    Views
    2,070

    I like the simple, self lit-up acrylic.

    I like the simple, self lit-up acrylic.
  9. Replies
    13
    Views
    2,159

    I use Everything from Inkscape, GIMP, AutoCAD,...

    I use Everything from Inkscape, GIMP, AutoCAD, and Paint 3D, but I use a commercial sign software to produce the final image/vectors, then import to Lightburn.
    Experiment and see what works for you...
  10. Replies
    22
    Views
    20,463

    Send me a message with an email address and I'll...

    Send me a message with an email address and I'll email to you.

    Thanks,

    James

    Here it is in a dropbox, The first file is an archive containing the rest.
    ...
  11. Replies
    22
    Views
    20,463

    There is another way. Make sure your USB cable...

    There is another way.
    Make sure your USB cable is a good one.
    I can send you the driver set that I have that I am using right now.
    I can tell you how to install.

    I need to know your ability...
  12. Replies
    22
    Views
    20,463

    Here is what I run: 420563420564 Running on...

    Here is what I run:

    420563420564

    Running on 1 physical and 2 virtual machines, all Win 10 64 bit though.
    Something to try maybe?
  13. Replies
    8
    Views
    2,439

    If you must solder... Remove the screw, Fab a...

    If you must solder... Remove the screw, Fab a piece of wire with a GOOD connector, solder to the screw, replace the screw.
  14. Replies
    22
    Views
    20,463

    I run 2.14.10 on 64bit Win 10. I installed the...

    I run 2.14.10 on 64bit Win 10.
    I installed the LMCUSB.sys driver set.
    Small enough to email.
    The driver is Intel/AMD specific.
  15. Replies
    8
    Views
    2,439

    I would use another method. Heat can cause your...

    I would use another method. Heat can cause your tube to shatter or create a weak spot.
    Use a terminal if possible.
    Sorry I didn't get back to you sooner, holiday here.

    James
  16. Replies
    8
    Views
    2,439

    Should have positive + at one end and negative...

    Should have positive + at one end and negative terminal at the other. You may need to attach one or the other.

    https://ae01.alicdn.com/kf/HTB1NQDUXNv1gK0jSZFFq6z0sXXaK.jpg
  17. I start with a low 50khz freq and 80% power to...

    I start with a low 50khz freq and 80% power to blast away material (I blast carbon build-up). Then use a higher freq 100khz and lower power 50% to finish. Check/adjust focus.
  18. Replies
    9
    Views
    1,981

    Make sure your grounds are good.

    Make sure your grounds are good.
  19. Replies
    9
    Views
    1,981

    Here are a couple of pics from my setup......

    Here are a couple of pics from my setup...
    419357419358
  20. Replies
    9
    Views
    1,981

    I would also like to add that you have an awesome...

    I would also like to add that you have an awesome machine!!!
    Get your "as built" drawing and schematic done as soon as you feel it's right.
    Photo every terminal block, controller connection, DIP...
  21. Replies
    9
    Views
    1,981

    I'll check some of my notes. When all else...

    I'll check some of my notes.

    When all else fails....

    "Calculatus Eliminatus"
    Dr. Seuss

    You are going in the right direction, keep plugging away Les, you will succeed!
  22. Replies
    9
    Views
    1,981

    Use voltmeter check voltages at critical points...

    Use voltmeter check voltages at critical points also check when pulsing, look for change.
  23. Replies
    14
    Views
    5,785

    This is a great place to get MUCH info on what...

    This is a great place to get MUCH info on what you are trying to do.
    Homing or perhaps Origin gets set from the first power-up of the controller.

    Do you have a drawing or schematic of your...
  24. Replies
    14
    Views
    5,785

    I'm assuming you have followed the steps in the...

    I'm assuming you have followed the steps in the "RDC644XG Controller User Manual"?

    If you are confident enough, smoke test.

    I would check the Lightburn Software forum also for tips.
  25. Replies
    2
    Views
    3,098

    .......I'm in a great mood, so I'll take one for...

    .......I'm in a great mood, so I'll take one for the group!

    First of all, welcome to the forum!

    There is no easy answer to these questions...
    That being said, there are a number of factors...
Results 1 to 25 of 35
Page 1 of 2 1 2