Search:

Type: Posts; User: larry senen; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. having had a small shop and now moving to a...

    having had a small shop and now moving to a smaller one, i would still get two machines.
  2. Replies
    7
    Views
    1,134

    the length of the piece @ 15' is the limiting...

    the length of the piece @ 15' is the limiting factor. most paper backed veneers are at 8' might find some at 10'
  3. i have layed up pieces to be curved on aircraft 3...

    i have layed up pieces to be curved on aircraft 3 ply,in the press. more stable than a veneer backer. used to get it from a place called anderson plywood.
  4. Replies
    14
    Views
    6,663

    I have used prefinished maple ply for cases, it's...

    I have used prefinished maple ply for cases, it's lighter in weight and more water resistant than melamine on particle board
  5. Replies
    8
    Views
    1,478

    wallpaper paste. heavy clay based.

    wallpaper paste. heavy clay based.
  6. run the face of the board against a running band...

    run the face of the board against a running band saw,backwards at a slight angle. the speed and angle will determine the amount of distressing.
  7. Replies
    12
    Views
    3,777

    378685378685these were alder

    378685378685these were alder
  8. Replies
    27
    Views
    3,000

    i used to make my own double ply with aircraft 3...

    i used to make my own double ply with aircraft 3 ply,but i laid it up in a vacuum press.then a contact cement to the piece . i would mask off the edges and use yellow glue on them. tape is enough to...
  9. I made a sliding fence/stop for a disc sander. I...

    I made a sliding fence/stop for a disc sander. I make small 8 sided boxes as a hobby. Various ways to make a sliding stop.
  10. Replies
    33
    Views
    5,467

    http://www.castleusa.com/products/castle-100-pocke...

    http://www.castleusa.com/products/castle-100-pocket-hole-machine.html?gclid=EAIaIQobChMImYiGy9r11wIVFNVkCh0xHgPrEAAYASAAEgInBPD_BwE

    new bench top model.
  11. i'm sure i'll get flamed for this,,, but jointer...

    i'm sure i'll get flamed for this,,, but jointer tables don't have to be"co-planar" just set the knives off the out feed table, and start your wood a few inches and then keep pressure on the out feed...
  12. Replies
    11
    Views
    1,729

    your idea of a routed line will work, but i think...

    your idea of a routed line will work, but i think i would make 4 fronts and glue/join them edge to edge.
  13. Replies
    8
    Views
    1,500

    planer/moulder is a great machine. have one for...

    planer/moulder is a great machine. have one for 20 years, accepts knives for making all kinds of profiles.
  14. Thread: miter cuts

    by larry senen
    Replies
    8
    Views
    1,396

    tape sounds right. or you could cut one end with...

    tape sounds right. or you could cut one end with the heel against the fence and one end with the toe on the fence ,just make sure you have one of each at the joint.
  15. milescraft. @ lowes and home depot. has an insert...

    milescraft. @ lowes and home depot. has an insert that accepts porter cable guides
  16. Replies
    31
    Views
    8,395

    the omer site is not clear on whether or not one...

    the omer site is not clear on whether or not one gun can drive plastic AND metal pins. does it?
  17. i have that same clamping straight edge, there's...

    i have that same clamping straight edge, there's a little slop in it. if you put pressure on the left edge with the square then cut on the right edge you'll get that result. so set it up by pushing...
  18. Replies
    27
    Views
    4,747

    try the orange one's at home depot, i too can't...

    try the orange one's at home depot, i too can't stand bad pencils, but the thin and thick ones are really good. i think the fat ones are.35 cents each. i have found decent ticondiroga's . they're...
  19. Replies
    27
    Views
    4,747

    get a tube of home depot pencils and it comes...

    get a tube of home depot pencils and it comes with a sharpener that you put in a hand drill. get the biggest drill you can find!
  20. Replies
    10
    Views
    1,867

    what seller has 10% off?

    what seller has 10% off?
  21. love my castle machine. lower, angle so less...

    love my castle machine. lower, angle so less movement when you screw the joint. but i still use a kreg hole if i plan on having the hole visible because of their plastic hole covers.
    it is a bit...
  22. Replies
    10
    Views
    1,937

    think of oven dried wood as sort of case...

    think of oven dried wood as sort of case hardened. you're releasing tension in the wood as you plane. if i'm making doors, i let the pieces move a few hours before final sizing.
  23. Replies
    38
    Views
    8,719

    can't go wrong with a 16" excaliber.sp ?i can...

    can't go wrong with a 16" excaliber.sp ?i can even use #00 blades with the right tension.
  24. Replies
    36
    Views
    4,239

    i think i would try an angled sled on a drill...

    i think i would try an angled sled on a drill press and use a small drum sander, the kind you get at harbor freight.
  25. Replies
    25
    Views
    4,435

    You shouldn't have snipe so bad that you have to...

    You shouldn't have snipe so bad that you have to cut it off. Something is not set up right.
Results 1 to 25 of 160
Page 1 of 7 1 2 3 4