Search:

Type: Posts; User: Don Morris; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. That makes sense about the moisture and having to...

    That makes sense about the moisture and having to be DRY. I'll just have to check and be sure everything is dry including the shoes I wear. Thanks for the heads up about that. I once walked on a...
  2. When can you walk on plants sprayed with Roundup

    I know about Non Hodg... Lymph... I just want to know when I can walk on the plants I will spray with Roundup so that I don't take residual spray to the rest of the yard. 30mins? 1 hr? Anybody with...
  3. Replies
    3
    Views
    417

    Thanks for the reply John, particularly the...

    Thanks for the reply John, particularly the "won't look perfect" comment. I will need to show that to LOML. The area is small, except to LOML.
  4. Replies
    3
    Views
    417

    Repair two dings on corner of desk top

    I bought a solid wood door, stained it and put a General Finishes poly on it, to be used by LOML as her desk top. We had to move it temporarily to a different room for a couple days, as that room's...
  5. Thanks for the heads up on Accurate Bearing....

    Thanks for the heads up on Accurate Bearing. That's the kind of advice I was looking for. Have all the measurements made except for the width. Will do that of course and give them a call tomorrow...
  6. Source for bearings in Porters Cable 7518 router

    I've had my PC 7518 router for almost 20 years. So I wasn't upset to hear, and feel the signs the bearings needed replacing. The folks over at Reproduction Woodworks do a great job of walking you...
  7. Replies
    18
    Views
    2,154

    This is being applied in the middle of summer, on...

    This is being applied in the middle of summer, on a very warm day after power washing the floor and making sure it is clean and dry. It should adhere really well. If that's the worst problem to worry...
  8. Replies
    18
    Views
    2,154

    Epoxy your garage floor...yes or no?

    My neighbors are doing this and I was wondering if this is "a good thing to do"? Anybody with experience with an epoxied floor?
    Thanks for any input!
  9. Replace or repair a Bosch 3107 DVS ROS sander

    I've had my Bosch sander for years. Been a work horse. But today, it stuttered then quit. I use an orbital sander enough that it's needed, no question about that. But when a unit is close to 10-15...
  10. Pony 3/4" bar clamps cost more, are they worth it?

    I have always loved my Pony 3/4" bar clamps. Some I've had in use for over 20 years, with little to no complaints on my part. I came up with an idea to use a pair on something not related to...
  11. General Metalworking Thanks guys for the straight talk and input. I...

    Thanks guys for the straight talk and input. I was looking at the Hitachi 72 tooth carbide tipped blade before going on the forum. It's not too expensive and meets the requirements stated above. I'm...
  12. General Metalworking I cut non ferrous metal rarely, but have a project that may need multiple cuts

    Most often I've used a Hack saw to cut thin aluminum and other similar thin non ferrous metals. However, I've run into a project that might call for cutting a number of fairly thin pieces of...
  13. New version of Porter Cable 4210 dovetail jig. Problem with narrow drawers.

    I had the old version of the PC dovetail jig and the new version for half blind dovetails looked like a better mouse trap. It was offered as a gift from LOML so I said Yes. Come to find out that...
  14. Replies
    12
    Views
    1,310

    Wow, lots of good ideas. I like the two nail...

    Wow, lots of good ideas. I like the two nail type. That almost looks idiot proof. That's for me. I don't do enough to justify trying to make or have someone make a holder, unless a task comes up that...
  15. Replies
    12
    Views
    1,310

    I've often thought that I might make some effort...

    I've often thought that I might make some effort to make sure the legs were absolutely parallel. That makes sense. When I pull the staples out of the box, some are surely not parallel. I'll give that...
  16. Replies
    12
    Views
    1,310

    I thought I knew how to use a hammer

    Does anyone else have trouble hammering in those large metal staples? The ones that are 1" x 1/2". I don't often use them, and usually not for woodworking. But once in a while, they come in handy...
  17. Success, just had to completely seal off the DD....

    Success, just had to completely seal off the DD. Went to what I thought were extraordinary efforts to assure the unit was sealed off...all bolts, nuts, plastic/wood junctions, etc. were again sealed....
  18. I sent Roy a PM, and he's right. I used a gasket...

    I sent Roy a PM, and he's right. I used a gasket material that was handy, not the best material. The original material I wanted to use was too thick, couldn't use it. I finished too late at night to...
  19. Replies
    61
    Views
    6,892

    We have the whole house 20K Generac. Yes it's...

    We have the whole house 20K Generac. Yes it's noisy when going, but after we went through the Derecho Storm that hit this DC area a few years back and left us without electricity for a week, LOML...
  20. Oneida DIY Dust Deputy not working as should. Can't figure out why.

    I had an original Oneida Dust Deputy for years. I forget what I did to damage it, but I did. So I decided to get one of the DIY $49.99 new tops and build a bottom out of 3/4 plywood to fit it and I...
  21. Thanks everyone, for their input and esp. the...

    Thanks everyone, for their input and esp. the local creekers who volunteered their wider cutting band saws. Creekers rock! Decided to use Jim Becker's suggestion and do a partial resaw on the TS...
  22. I'm looking at my pitiful old Delta 14" and...

    I'm looking at my pitiful old Delta 14" and feeling so low. Enjoy!
  23. Need to re-saw one 7 1/2" x 38" board. My Delta only does 6". Live in Metro DC area.

    I have all the highly figured cherry for a bedside chest; but want to use one particular board for the top. The board is 7 1/2" W X 38" L X 11/16". Re-sawing it once would give me two pieces that...
  24. Replies
    50
    Views
    4,628

    I did the same thing only took off the tip of the...

    I did the same thing only took off the tip of the middle finger of the hand not involved in pushing the wood through the guard. So I understand your situation. I was using a large push block to push...
  25. But I'm still going to try dovtails on 5/8"...

    But I'm still going to try dovtails on 5/8" pieces and if that all looks OK, I'll probably just end up thickness planning everything to that and away we go.

    Don M
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4